Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Installation for Whitney Homeowners
A gate that won’t open drains a corner of your day. A gate that opens when it shouldn’t drains something bigger. In Whitney, where a lot of homes sit on deep lots with wide driveway aprons and side-yard setbacks generous enough for a real gate, the install has to fit the property, not a catalog. Our technicians have up to 13 years of experience and are trained across nine gate-automation brands, so the crew on your driveway knows how a swing arm behaves in a tight pillar line and how a slider clears a low block wall. We schedule free estimates throughout Whitney, and a live person answers the phone 24 hours a day, 7 days a week. Call (855) 928-1304 and we’ll get you a written price before anything gets ordered or bolted down.
What Our Gate Installation Service Includes
Driveway Gate
A driveway gate is the main entrance to your property, and on a typical Whitney lot it needs to clear the easement, back off far enough for a car to wait, and swing or slide without clipping a curb. You need one when the old gate has racked beyond adjustment, when a wall has settled, or when you are fencing the property line for the first time. We measure the opening, check the grade and footing, and set the posts so the gate hangs square from day one rather than dragging six months later.

Pedestrian Gate
A pedestrian gate is the walkway entrance – the one people actually use every day to take out the trash or check the mailbox – so it matters more than most homeowners expect. You need a new one when the latch has worn through the stile, the hinges have pulled, or the frame no longer meets square and won’t self-close. We build these to fit the walkway width and set the hinges so the gate swings free without rubbing the post.

Sliding Gate
A sliding gate runs along the fence line instead of swinging out, which is why it fits driveways in Whitney where there simply isn’t room for a swing arc. You need one when a swing gate would foul the street, block a sidewalk, or hit a parked car. We set the track or cantilever system so the gate rolls true, handle the operator mounting, and make sure the gate stop and guide are lined up before we call the job done.

Swing Gate
A swing gate is the classic pair of leaves on hinges, and it is the right answer for wider entrances where a slider isn’t practical. You need one when your driveway entrance runs 12 feet or more and you want the look of a hung gate rather than a rolling one. We set the hinge posts, check the plumb, and fit the leaves so they meet cleanly at the center rather than binding or gaping.
Double Gate
A double gate is two leaves that meet in the middle, the standard for most driveways where you want full-width clearance and a clean center seam. You need one when you want a gate wide enough for trucks, trailers, or a boat without the visual weight of a single oversized leaf. We hang both leaves off matched posts and align the drop rod and latch so the two halves close together rather than fighting each other.
Security Gate
A security gate is built for controlled entry – keypad, intercom, card reader, or a locked pedestrian gate – and it starts with the gate itself, not the electronics. You need one when you want to know who is coming up the drive, or when a property has been open to the street too long. We build the gate to carry the access control hardware, then wire it in so the entry control works with the operator instead of fighting it.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Brands We Service for Gate Installation
Automation is only as good as the gate it’s bolted to, but the operator still matters. We work with Ghost Controls on residential driveway jobs where a simple, reliable solar or low-voltage operator fits the property, and we know where their control boards and battery connections tend to give trouble. We handle DoorKing on access-controlled entrances, including the keypad and entry hardware that goes with it. Elite operators come up on heavier slide gates where the torque and duty cycle have to match the leaf weight. Each of these has its own mounting pattern, its own limit-switch behavior, and its own quirks once the weather turns, and we’ve learned them from the inside of the housing rather than the install manual.
Whether you have Mighty Mule on an existing gate you want matched, or a brand not on the list, we can help. Our technicians are trained across nine major gate-automation brands, so the correct parts and the correct setup are known before we arrive. If the gate is being replaced rather than repaired, we size the operator to the new leaf – the brand follows the job, not the other way around.
Signs You Need Gate Installation Right Now
- The gate sags or drags on the ground. A leaf that scrapes the pavement has usually lost its footing or its hinge post has shifted, and adjusting the hinge won’t fix a post that has moved. Left alone, the operator has to fight the drag, which shortens its life.
- The posts are loose or the wall has cracked around them. Loose posts mean the gate is relying on the latch and operator to hold it up, and that is the failure mode that breaks both. If the concrete is breaking away around the post, the footing needs attention before the gate can hang right.
- The gate no longer closes flush or meets at the center. A gap or an overlap at the center means the leaves or posts have moved out of square. That misalignment is what wears out latches, bends drop rods, and eventually stops the gate from latching at all.
- The opening is too tight for your vehicle or trailer. If you’ve started parking a bigger truck or hauling a trailer, the old gate width stops working. Widening or replacing the gate is a measure-and-build job, not a hinge adjustment.
- You are fencing the property for the first time. A new fence line needs the gate hung to match it, with posts set to the right depth and the operator wired in from the start. Doing it in the right order saves tearing out fresh concrete later.
Our Gate Installation Process – Step by Step
- 1
Free on-site estimate and measure. We come out, measure the opening, check the grade, and look at the power source and footing before quoting a price. You get a written estimate with the gate, hardware, and automation line items clear, and we don’t start until you’ve agreed to it.
- 2
Order the gate and hardware. Gate work is measured and built to fit, so the material is ordered once the numbers are confirmed. That means an accurate fit and no trimming on site – and a realistic schedule rather than a promise of same-day service.
- 3
Set the posts and footing. Correct footing depth and concrete set are everything for a gate that stays true. We set the posts plumb, let the concrete cure, and verify the hinge line before the gate goes up.
- 4
Hang the gate and fit the hardware. The gate is hung, checked for square and swing, and the hinges, latch, drop rod, and stops are fitted. We test the full travel by hand before any operator is connected.
- 5
Wire the operator and access control, then test. We mount the operator, run the power and safety edges, and set the limits. Every cycle is tested – open, close, reverse, and entry control – before we hand you the keys and walk you through it.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Installation Cost in Whitney?
A typical pedestrian gate in Whitney runs $900 – $1,800 installed, and a single-leaf driveway swing gate runs $2,400 – $4,500 depending on width, material, and whether an operator is included. A sliding gate with automation usually lands between $3,500 and $7,000, and a double gate or security gate with access control runs higher because of the extra hardware and wiring. Those ranges reflect the local market – wide driveways, block walls, and desert-grade footings all affect the number.
What moves the price: gate width and material (steel versus ornamental aluminum), whether you need a new footing or can use an existing one, the operator brand and duty cycle, and whether access control or safety edges are part of the job. The best way to avoid overpaying is to get the measure right the first time and to have the estimate broken into gate, hardware, and automation so you can see what you’re paying for. Every estimate is free, and the price is quoted and agreed before any work starts – no surprises on the bill.
We also stand behind every job with our written 90-Day Done Right Promise: if it isn’t right, we come back and make it right, no paperwork and no arguing.
Gate Installation Near Whitney – Our Service Area
We serve Whitney and the surrounding valley, including Gate Installation in Sunrise Manor, Gate Installation in Paradise, Winchester, Henderson, and North Las Vegas. Estimate scheduling is quick across the east side of the valley and a bit longer for outlying areas like Boulder City or Sandy Valley. Start at our home page to see the full scope, or go straight to Gate Installation in Whitney for the local details.
Serving Whitney, NV – Our Local Coverage Area
We serve Whitney and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Gate Installation in Whitney
Gate installation is the measure, build, and hang of a new gate – driveway, pedestrian, sliding, swing, double, or security – including the posts, footing, hardware, and any operator or access control wired in with it. It is the complete job, not a repair or adjustment of an existing gate. We handle the full scope from hinges and welds to keypads and automation.
Most gate installations take one to three days on site, once the gate and hardware are ordered and on hand. The build and delivery time for a made-to-fit gate adds to that schedule, which is why we measure first and quote a realistic date rather than promising same-day work. Footing cure time is part of the plan, not a delay.
Gate installation in Whitney typically runs from about $900 for a pedestrian gate up to $7,000 or more for a sliding or security gate with automation and access control. The final number depends on width, material, footing, and operator brand. Call (855) 928-1304 for an exact quote – estimates are free.
Yes. We are trained and equipped on nine major gate-automation brands, including Mighty Mule, Ghost Controls, DoorKing, and Elite, so we can size and set the right operator for your new gate. If you already have an operator you want to keep, we’ll tell you honestly whether it fits the new leaf.
Yes. A live person answers the phone 24 hours a day, 7 days a week, so if a gate is stuck open or won’t close, you aren’t waiting until Monday morning. Keep in mind that new installation is scheduled work, but emergency repair of an existing gate is where our fast response lives.
Every job is covered by our written 90-Day Done Right Promise – if something isn’t right, we come back and fix it, with no paperwork and no arguing. It’s the same standard on every gate job, from a single pedestrian gate to a full security entrance.
Clear the driveway and the gate opening of vehicles, trash cans, and anything parked in the work area, and make sure we can reach the power source. If you have an HOA, check the approval before the estimate. Beyond that, we handle the rest – measure, footing, hang, and wiring.
Schedule Your Gate Installation Service in Whitney Today
If your gate is sagging, your opening is too tight, or you’re fencing the property for the first time, call (855) 928-1304 for a free, no-obligation estimate in Whitney. A live person is here 24 hours a day, 7 days a week. We measure first, quote a fair price in writing, and back the work with our 90-Day Done Right Promise. For repairs on an existing gate, see Gate Repair and Gate Motor & Opener.
Written by the team at Ironworks Gate Co.