Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Parts & Welding Across Whitney
If your gate is dragging, sagging, or the operator has quit, we handle gate parts and welding in Whitney and we can usually get out to you the same day you call. Whitney is a community we know street by street, from Warm Springs Road down through the tract neighborhoods south of the airport, and we’ve seen the same problems here for years: sun-baked hinges, heaving posts, and builder-grade gates that were never built for this desert. Our team specializes in gates only, so the parts and the welding are the job, not a side job. Call (855) 928-1304 and a live person will pick up, day or night.
Why Ironworks Gate Co. Whitney Is Whitney’s Preferred Gate Parts & Welding Company
We’ve built a reputation in Whitney by showing up, doing the repair once, and standing behind it in writing. Most folks we work with have lived in their home for twenty years or more, and they’ve dealt with enough fly-by-night outfits to know the difference between a patch and a real fix. When we look at your gate, we’re looking at the whole system: the posts in the ground, the hinges taking the load, the operator running the arm. That’s why Whitney homeowners call us back.
Whitney customers tell us the same thing: we answer the phone, we quote the price before we touch anything, and the bill matches the quote. Our 90-Day Done Right Promise is written and simple – if it isn’t right, we come back and make it right, no arguing. We know how long it takes to get to your part of Whitney, because we work these neighborhoods constantly. That means fewer trips wasted and a straight answer about when we’ll be there. Live support answers (855) 928-1304 around the clock, so a gate that fails on a Sunday still gets a real person.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Gate Parts & Welding Services in Whitney
Most of what we do in Whitney is bringing older gates and legacy operators back to reliable service. Here are the parts and welding jobs that come up most.
Hinge Replacement in Whitney
Rusted hinges on builder-grade ornamental gates are one of the most common calls we get in Whitney, because decades of poor irrigation drainage leave water sitting right at the hinge joint. When that hinge is worn, the gate sags and the latch stops lining up. We replace the hinge, check the load it’s carrying, and make sure the gate swings true again.

Post Replacement in Whitney
When the hinge post has heaved or settled, swapping parts won’t fix the drag – the post itself is the problem. In Whitney we regularly see hinge posts shift in the caliche-hard soil off Warm Springs Road after monsoon saturation, and the gate starts dragging or missing its latch within a season. We reset or replace the footing and post so the gate hangs where it should.

Rail Repair in Whitney
A bent or cracked rail throws off the whole alignment, and on tubular steel gates it’s usually the frame that takes the hit. We straighten or replace damaged rails and re-weld the joints so the gate keeps its square. That matters more here than in cooler climates, where 110°F summer heat keeps expanding the metal.

Custom Welding in Whitney
Sometimes the same old builder hardware just keeps failing, and a small custom weld fixes a weakness the original manufacturer never planned for. Our welding work in Whitney includes reinforced hinge tabs, repaired corners, and welded stops that hold up to the heat and the monsoon cycle. We weld on site where we can, so the gate isn’t down for days.
For the full scope of what we handle, see our Gate Parts & Welding services.
Trusted Brands We Service in Whitney
We’re trained and equipped on nine gate-automation brands, including Linear, Viking, and DoorKing, along with LiftMaster, FAAC, BFT, Ghost Controls, Elite, and Mighty Mule. Plenty of Whitney driveways still run legacy Linear and LiftMaster operators, and we know those older control boards and their failure patterns. We don’t stock parts on trucks; we diagnose the fault, source the right part, and turn it around quickly. When a board is obsolete, we’ll tell you plainly and lay out the retrofit against replacement so you can decide.
See the difference
Before
After
Before
After
Before
AfterCommon Gate Parts & Welding Problems We See in Whitney Homes
- Hinge post heave. Whitney’s caliche-hard soil off Warm Springs Road cracks and settles after monsoon rains, shifting the footing and making the gate sag or miss its latch within a season – a problem we rarely see where the ground is sandier and more stable.
- Obsolete control boards. Legacy LiftMaster and Linear gate operators in Whitney often run boards that fail under 110°F summer heat, leaving the gate stuck open or mid-travel.
- Rusted hinges and rollers. Poor irrigation drainage on builder-grade ornamental gates keeps moisture at the hinge and roller, and the rust eats the joint before the gate is due for anything else.
- Misaligned safety photocells. Older safety eyes that no longer line up stop the operator mid-cycle, and on gates hung before modern entrapment protection, the fix is more than a nudge.
Pricing for Gate Parts & Welding in Whitney, NV
Pricing is settled before we turn a single bolt, and the bill matches the quote. Here’s what Whitney jobs typically run:
| Job | Typical Whitney Range |
|---|---|
| Hinge replacement (per gate) | $150 – $320 |
| Post reset or replacement | $300 – $750 |
| Rail repair / re-weld | $180 – $450 |
| Custom welding (reinforced tabs, corners, stops) | $150 – $500 |
| Roller replacement | $90 – $200 |
| Latch & lock adjustment or replacement | $100 – $275 |
What moves the number: whether the footing needs resetting, how far the metal has rusted through, and whether the operator needs service alongside the parts. Replacing a worn hinge is straightforward; correcting a heaving caliche footing is more work but fixes the sag for good. Call (855) 928-1304 for a free estimate – it costs nothing and we’ll quote it straight.
We Also Serve Cities Near Whitney
We take gate parts and welding jobs across the east side of the valley, including Sunrise Manor, Winchester, Paradise, and Las Vegas. If you’re just outside Whitney, we can still get to you. See everything we handle on our Whitney page, or call and we’ll confirm your area.
Serving Whitney, NV – Our Local Coverage Area
We serve Whitney and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs – Gate Parts & Welding in Whitney
In Whitney, it’s usually the post. Monsoon water saturates the caliche soil, the hinge post heaves or settles, and the gate drags even though the hinges are fine. A properly trained pro will check the footing before replacing parts, because a new hinge on a shifted post won’t fix the drag. Call (855) 928-1304 for a free estimate and we’ll diagnose it on site.
Yes, most legacy LiftMaster operators can be retrofitted with modern safety photocells and entrapment protection. The operator’s control board needs to support the connection, so we check the board first before we recommend the parts. Call (855) 928-1304 and we’ll tell you what your unit can take.
Common signs are the gate stalling mid-travel, reversing without warning, or the remote failing to trigger – especially in Whitney’s summer heat, which is hard on aging boards. If the board is discontinued, a qualified pro will tell you plainly and lay out retrofit versus replacement. Call (855) 928-1304 for a straight diagnosis.
Sometimes, and sometimes the better fix is replacing the hinge. If the hinge tab itself has rusted through, welding a new tab in place is often the right repair; if the whole hinge joint is gone, replacement holds up longer. We look at the metal before we recommend either. Call (855) 928-1304 for a free estimate.
For a Whitney gate with a solid frame and a heaving footing, retrofitting parts and resetting the post is usually cheaper than a full replacement – often hundreds rather than thousands of dollars. Replacement makes sense when the frame itself is bent or the operator is beyond retrofit. We’ll give you both numbers so you can decide. Call (855) 928-1304.
If your gate is dragging, the latch won’t catch, or the operator has quit, the fastest way to sort it out is to call us. We’ll quote it before we start, we’ll do the work once, and we’ll stand behind it in writing with the 90-Day Done Right Promise. Call (855) 928-1304 for a free estimate on gate parts and welding in Whitney.
Written by the team at Ironworks Gate Co.