Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Parts & Welding Across Sunrise Manor
When a driveway gate starts dragging after a dust storm or a post leans after a hard rain, Sunrise Manor homeowners call us because we know this ground. The hard caliche under most lots here means a post repair is a different job than it is in a newer community, and the wide block-wall driveway gates common along Boulder Highway and the 89110 corridor need the right parts on hand. We quote the work before anything starts, and our technicians bring up to 13 years of experience to each job. Call (855) 928-1304 and a live person will answer, day or night.
Why Ironworks Gate Co. Whitney Is Sunrise Manor’s Preferred Gate Parts & Welding Company
We’re not the cheapest bid in the east valley. We’re the call you make once and don’t have to make again. Sunrise Manor isn’t a master-planned subdivision of tiny patio gates; it’s a wide, unincorporated stretch of larger lots and older ranch homes where full driveway gates and side-yard RV gates do the real work, and we treat that job with the care it deserves. Our standing offers are real: $50 off any repair over $250, a free second opinion on any written estimate, and a permanent 5% senior and veteran discount.
The company’s own service record is built on the same promise on every street in Sunrise Manor: the 90-Day Done Right Promise. If a weld cracks or a hinge fails after we’ve been out, we come back and make it right, in writing, no arguing. We also stand behind our work with a background-checked, uniformed technician on every job, working in your yard the way we would in our own mother’s.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Gate Parts & Welding Services in Sunrise Manor
The heat and dust here wear down the same parts year after year on wide block-wall and side-yard gates. Here’s where we spend most of our time in Sunrise Manor, and what a fair price looks like.
Hinge Replacement in Sunrise Manor
Corroded hinges are one of the most common calls we get on the double-swing driveway gates that are everywhere in the older parts of Sunrise Manor. When a hinge seizes or the weld holding it gives, the gate drops and drags against the block wall. A typical hinge replacement in Sunrise Manor runs $120 – $260 per gate leaf, and we set the hinge square so the gate swings true again instead of binding on the post.

Post Replacement in Sunrise Manor
This is the Sunrise Manor job that trips people up. The soil here is hard caliche, and a hinge post that has shifted in saturated ground often can’t be re-set with a shovel. We break up the caliche properly, set the post in a proper footing, and check that the gate still clears the wall on a wide sliding run. A typical post replacement in Sunrise Manor runs $350 – $750 depending on post size, footing depth, and whether we’re replacing a metal or block-set post.

Rail Repair in Sunrise Manor
Wind-driven dust and UV bake the rails on older wrought-iron and chain-link gates until joints rust and rattle. We reweld broken rails, replace bent sections, and check that the gate frame is still square before it goes back on the track. A typical rail repair in Sunrise Manor runs $95 – $280.

Custom Welding in Sunrise Manor
When a gate needs a bracket, a support gusset, or a new latch plate that isn’t in any catalog, we fabricate it on site. Custom welding in Sunrise Manor runs $110 – $300 for most small fabrications, and we test every weld under load before we sign off. No gate is put back into service until we’re sure it will hold.
All of this work falls under our Gate Parts & Welding team. Whatever’s on your driveway, we have the tools and the training to get it fixed right the first time.
Trusted Brands We Service in Sunrise Manor
We’re trained and equipped across nine gate-automation brands, including FAAC, BFT, Linear, and Viking, so we can diagnose and repair the operator controlling your gate rather than guessing. When a motor component fails, we source the correct part and get it to your gate on a scheduled visit. No part stash is carried on a truck, but we know these operators well enough to identify what’s wrong on the first call and quote the right fix. Whether your Sunrise Manor gate runs a FAAC swing operator or a Linear slide unit, the correct fix is made on the first scheduled visit.
Common Gate Parts & Welding Problems We See in Sunrise Manor Homes
- Wind-driven dust jams rollers and racks on block-wall driveway gates. Fine grit from east-valley dust storms works into the rollers and the rack and pinion, and the gate starts binding and travelling unevenly. A roller cleaning that turns up a shifted roller carriage can quickly turn into a post-footing job.
- Monsoon runoff undermines post footings in unpaved side yards. Saturated soil around an older post causes it to lean, and the gate then sags or drags on the track. On caliche ground, that post usually can’t be re-set with a shovel.
- Extreme heat bakes lubricants and UV-degrades operator housings. Summer highs above 105°F dry out every moving part, and the sun cracks keypad faces and safety photocell lenses. The operator may still open, but the safety sensors can stop working without warning.
- Older gate hardware on 1950s – 1980s ranch homes is simply worn out. Latch assemblies rust solid, hinges seize, and rollers flat-spot after decades of use. Replacing those parts properly restores a gate that was built to last.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Parts & Welding in Sunrise Manor, NV
Sunrise Manor gate work is priced by the job, not the hour. A typical roller cleaning and lubrication runs $90 – $180, and if the rollers are flat-spotted or the carriage has failed, new rollers run $140 – $320 for a two-roller set. Hinge replacement runs $120 – $260 per gate leaf, post replacement $350 – $750, and custom welding $110 – $300 for most small fabrications. What moves the number is the ground: a caliche footing takes more work than a standard set, and a wide double-swing gate needs more time than a single leaf. Every price is quoted and agreed in writing before we start. Call (855) 928-1304 for a free estimate, and ask about the $50 off any repair over $250.
We Also Serve Cities Near Sunrise Manor
Sunrise Manor sits right up against Whitney, Winchester, Las Vegas, and North Las Vegas, and we serve gate parts and welding work in all of them. If you’re in a neighboring community, see our Gate Parts & Welding in Sunrise Manor page and ask us about scheduling to your area. The same upfront pricing and 90-Day Done Right Promise goes with us.
Serving Sunrise Manor, NV – Our Local Coverage Area
We serve Sunrise Manor and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs – Gate Parts & Welding in Sunrise Manor
Because the east-valley dust is fine enough to work past the roller seals and pack into the bearing surfaces, and a wide block-wall gate gives that grit plenty of track to travel. The fix is to clean and re-lubricate the rollers, check the rack and pinion if the gate is motorized, and correct any sag at the hinge post. Left alone, grit scores the roller and shortens its life. Call (855) 928-1304 for a free estimate.
Yes, in most cases the post can be re-set or replaced on its own without touching the rest of the fence. The catch in Sunrise Manor is the caliche: it’s hard enough that a shifted post often needs a breaker bar to free and re-set, not just a shovel. We set the new footing properly, check the gate clears the wall on a wide sliding run, and confirm the manual release works before we finish. Call for a free second opinion on any written estimate.
Use the manual release lever or key that came with your operator, which on most residential operators is a lever you pull or a key you turn to disengage the drive so the gate can be pushed by hand. Do the release with the power off and the gate fully stopped, stand clear of the gate’s path before you push, and don’t force a gate that won’t move freely. If you’re not sure how yours works, call us before a storm and we’ll show you the correct release for your brand.
Yes. Any automatic gate operator on a residential driveway needs working safety sensors that stop or reverse the gate when something is in its path, and the sensors are the part most often lost to heat and dust here. We test the photocell on every scheduled visit and replace failed sensors before we sign off. A gate that opens on its own without working sensors is a hazard. Call for a scheduled sensor check.
We’re trained and equipped on nine major brands, including FAAC, BFT, Linear, and Viking. That range means we identify the correct fix on the first scheduled visit rather than guessing at your operator. We source the right part and get it to your gate without a runaround on stock. Call (855) 928-1304 and tell us the brand and model on your gate.
Call Ironworks Gate Co. Whitney for Gate Parts & Welding in Sunrise Manor
When a Sunrise Manor gate drags, leans, or jams after a storm, we’ll be there when we say, quote the work before anything starts, and back it with the written 90-Day Done Right Promise. Call (855) 928-1304 for a free estimate. A live person answers every call, day or night.
Written by the team at Ironworks Gate Co.