Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Repair for Whitney Homeowners
A gate that won’t open, drifts off its hinges, or grinds to a stop halfway down the driveway is the problem we solve every week in Whitney. Gate repair here usually runs $185 – $420 for the common failures – a dead opener board, a binding hinge, a misaligned post, a rusted weld – and most of those jobs are finished in a single visit. Our technicians have up to 13 years of experience on driveway and estate gates, and every repair is backed by our written 90-Day Done Right Promise. Same-day service is often available in Whitney, and a live person answers the phone 24 hours a day. Call (855) 928-1304 and we’ll get you a straight answer and an upfront price.
What Our Gate Repair Service Includes
We handle the full range of gate repairs – from the weld at the hinge to the circuit board in the operator. Here’s what each one covers, and how you’ll know it’s time to call.
Electric Gate Repair
Electric gate repair covers the low-voltage side of the system: the transformer, the control board, the wiring and the safety loop or photo-eye that tells the gate something is in the way. You need it when the gate powers up but won’t move, moves in one direction only, or stops and reverses for no clear reason. In Whitney we often trace failures to sun-baked control boxes and wiring that’s been chewed by desert rodents, and we test the whole circuit rather than swapping parts until something works. If the fault is upstream at the panel, we’ll tell you plainly and point you to a licensed electrician.

Automatic Gate Repair
Automatic gate repair focuses on the operator itself – the motor, gearbox, limit switches and the arm or slide mechanism that actually drives the gate. You need it when the gate moves slowly, squeals, slams at the end of its travel, or the opener beeps and gives up. We’re trained on nine gate-automation brands, so we can diagnose a control board fault on a DoorKing slide operator or a worn drive gear on a LiftMaster swing arm without guessing. Most operator repairs are done on the first visit with the correct part ordered ahead of time.

Hinge & Post Repair
Hinges and posts take the weight of the whole gate, and they fail quietly – a few degrees of sag here, a little more drag there – until the gate won’t latch. You need this repair when the gate scrapes the ground, hangs unevenly, or a post has shifted after a summer of ground movement. We reset and re-weld hinges, brace or replace a failing post, and check the footing so the fix holds. A gate hung on a rotten or loose post will never stay square, so we always fix the foundation before the gate.

Gate Realignment
Realignment is the correction of a gate that has dropped, twisted, or drifted out of square with its posts. You need it when the gate binds in the middle of its swing, rubs the post on one side, or leaves a gap that lets the latch miss. We measure the frame, adjust the hinges and stops, and true up the gate so it closes cleanly and the operator isn’t fighting the metal. A square gate runs quieter, lasts longer, and puts far less strain on the motor.
Lock Repair
Lock repair covers the latch, the keypad, the strike and the mechanical or electronic lock that holds the gate shut. You need it when the key won’t turn, the keypad ignores your code, or the gate latches but doesn’t actually secure. We repair mechanical latches, replace worn strikes, and check keypads and intercoms for wiring or battery faults. If the lock is part of a larger access-control setup, we can sort that at the same visit.
Weld & Rust Repair
Weld and rust repair is the metalwork side of the trade – broken hinge welds, cracked frame joints, and the surface rust that takes hold in Whitney’s dry heat and occasional monsoon moisture. You need it when you see rust bleeding down the gate, a hairline crack at a joint, or a hinge that has torn away from the frame. We cut out the failed section, weld in new steel, and treat the area so it doesn’t rust straight back. A proper weld on a gate frame is the difference between a repair and a repeat visit.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Brands We Service for Gate Repair
We’re trained and equipped on nine gate-automation brands, and we know where each one tends to wear out. Ghost Controls solar and low-voltage operators are common on rural and larger lots around Whitney, and we know their battery and controller quirks well enough to diagnose them without a parts cannon. DoorKing slide and swing operators show up on longer driveways, and we’ve seen their limit switches and loop detectors fail in predictable ways after a few summers of heat.
Elite operators are another brand we handle regularly, and their control boards are a frequent culprit when a gate powers up but won’t move. We also work on Mighty Mule and the rest of the major makes, and the first-visit fix rate comes down to knowing the brand’s failure pattern rather than guessing. Whether you have a Ghost Controls, a DoorKing, an Elite, or any other make on the driveway, we can help. If you’re not sure what’s installed, a photo of the operator label is enough for us to start.
Signs You Need Gate Repair Right Now
- The gate won’t open or close. If the operator clicks or beeps but nothing moves, the fault is likely in the control board, the battery, or a safety device. Driving it manually can strain the gearbox, so it’s better to have it looked at before you force it.
- The gate moves slowly or grinds. A gate that drags or shrieks is usually fighting a binding hinge or a sagging post, and the motor is paying for it. Left alone, a cheap hinge repair turns into an operator replacement.
- The gate doesn’t close all the way or reverses on its own. This points to a misaligned gate, a failing limit switch, or a safety edge that needs attention. A gate that won’t latch is a security problem, and it’s one we can usually correct the same day.
- You see rust, cracks, or a broken weld. Rust streaks and hairline cracks at the hinge or frame are early warnings that the structure is giving way. Catching them early keeps the repair small.
- The keypad, lock, or remote stops working. Intermittent access is often a battery, wiring, or keypad fault rather than a dead system. We diagnose the whole chain – remote, receiver, keypad, lock – before recommending any replacement.
Our Gate Repair Process – Step by Step
Here’s exactly how a repair visit runs, from your first call to the final test.
- 1
Call and describe the problem. A live person answers 24 hours a day, and we ask a few questions to understand the symptom – what it’s doing, what brand is installed, and how long it’s been acting up. That helps us arrive with the right diagnostic tools and a sense of what’s likely wrong.
- 2
On-site diagnosis. We test the operator, the wiring, the safety devices, and the gate’s mechanical alignment, then separate the electrical fault from the mechanical one. This step is where most gate repairs are won or lost, so we don’t rush it.
- 3
Upfront written price. Before any work starts, we explain what we found and give you a clear, itemized price. You approve it or you don’t – nothing gets turned, welded, or replaced until you’ve agreed to the number.
- 4
The repair. We complete the work with the correct parts for your brand, whether that’s a control board, a hinge weld, a realignment, or a latch repair. Most jobs are finished on that first visit.
- 5
Test and walkthrough. We cycle the gate several times, check the safety reverse and the latch, and show you what was done. Then we leave you with the written 90-Day Done Right Promise – if it’s not right, we come back and make it right.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Repair Cost in Whitney?
Gate repair pricing in Whitney depends on whether the fault is mechanical, electrical, or both, and how deep the diagnosis has to go. Here are the ranges we see most often:
- Hinge, post, or realignment repair: $185 – $340, depending on whether a post needs bracing or replacement.
- Weld and rust repair: $220 – $400, based on how much steel has to be cut out and replaced.
- Lock and keypad repair: $150 – $300, depending on the hardware and whether wiring is involved.
- Automatic gate / operator repair: $260 – $620, driven by the brand and the part – a control board costs far more than a limit switch.
What moves the price most is the part itself, the brand of operator, and whether the gate also needs mechanical realignment to stop the fault from coming back. You avoid overpaying by getting a written price before work begins, asking what’s included, and getting a second opinion on any large estimate – we offer one free on any written estimate you’ve already received. Our free estimate includes the full diagnosis, a written line-item price, and a clear explanation of what we’d fix and why. Call (855) 928-1304 for an exact quote on your gate.
Gate Repair Near Whitney – Our Service Area
We serve Whitney and the surrounding east valley, including Sunrise Manor, Winchester, Paradise, Henderson, and Enterprise. Response times vary with the day, but same-day slots are often available for Whitney and the nearby neighborhoods. If you’re just up the road, see our Gate Repair in Sunrise Manor page, and for the central valley, our Gate Repair in Paradise page. For the full scope of what we do, start at our home page.
Serving Whitney, NV – Our Local Coverage Area
We serve Whitney and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Gate Repair in Whitney
Gate repair is the diagnosis and correction of anything that stops a gate from opening, closing, locking, or running safely – from a broken weld to a failed control board. It covers the mechanical side (hinges, posts, alignment, welds, locks) and the electrical side (operator, wiring, safety devices, keypads). In Whitney, most gate repair visits involve one fault on each side, so we check both. Call (855) 928-1304 and we’ll tell you what your gate likely needs before we arrive.
Most gate repairs are finished in a single visit, typically one to three hours on site depending on the fault. A hinge or realignment job is quick; an operator board replacement or a weld repair takes longer because of the testing and cleanup. If a part has to be ordered for your brand, we schedule the return visit and complete the work then. We’ll give you a realistic time window when you call (855) 928-1304.
Most gate repairs in Whitney fall between $150 and $620, with the exact price set by the part and the labor involved. Hinge and realignment work tends to sit at the low end, while operator and control-board repairs run higher. You get a written, upfront price before any work starts, so there are no surprises on the bill. Call (855) 928-1304 for an exact quote – estimates are free.
Yes. We’re trained and equipped on DoorKing, Mighty Mule, and seven other major gate-automation brands, so we can diagnose the specific failure pattern for your operator. That means the correct fix on the first visit in most cases, rather than a trial-and-error parts swap. If you’re not sure what’s installed, a photo of the label on the operator is enough for us to identify it. Call (855) 928-1304 to book a diagnostic.
Same-day service is often available in Whitney, and a live person answers the phone 24 hours a day for urgent problems. If your gate is stuck open, won’t latch, or the operator is failing, call (855) 928-1304 and we’ll tell you honestly whether we can get to you today. If a part has to be ordered, we’ll secure the gate and schedule the return visit. We don’t leave a gate in a state that’s worse than we found it.
Yes. Every completed repair is covered by our written 90-Day Done Right Promise, the Keystone Standard we apply to every gate job. If something we fixed isn’t right, we come back and make it right – no paperwork, no arguing, no exceptions. That coverage applies to the work we performed, and we’ll explain exactly what it covers before you approve the job. Call (855) 928-1304 if you have a question about coverage on your gate.
Clear the driveway and the area around the gate so we can work safely and test the full travel of the gate. If you have the operator manual or a photo of the brand label, have it handy – it helps us arrive with the right diagnostic tools. Note when the problem started and whether it’s constant or intermittent, since that points to the likely cause. Then just call (855) 928-1304 and we’ll take it from there.
Schedule Your Gate Repair Service in Whitney Today
If your gate is stuck, sagging, or making a noise it didn’t used to make, call Ironworks Gate Co. Whitney at (855) 928-1304. A live person answers 24 hours a day, we quote an upfront price before any work starts, and every repair is backed by our written 90-Day Done Right Promise. Estimates are free, and same-day service is often available in Whitney. One call, done right, and backed in writing.
Written by the team at Ironworks Gate Co.