A Ironworks company - serving Whitney, NV

Linear Keypad & Intercom Repair in Whitney, NV

Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

Linear Keypad & Intercom Repair: The Whitney Owner’s Guide

Linear keypad and intercom repair in Whitney typically runs $185 to $340 installed, depending on whether the keypad, the intercom station, the wiring, or the control-board connection is what failed. We handle Linear keypads and intercoms as a service call, and on a straightforward swap we can often get out the same day you call. We’re an independent service provider, not affiliated with Linear, and we’ll say plainly which failure we found once we’ve tested it.

Call (855) 928-1304

Owners usually find this part has gone bad the same way. The gate stops answering the code that used to work, or the intercom goes quiet and the driveway caller is left talking to static. Sometimes the keypad backlight is still on, which makes it worse: the button lights up, the gate doesn’t move, and you start to wonder whether it’s the gate or the box on the post. In Whitney, sun-faded keypad faces and moisture in the post are the two things we see first, followed by a failed control-board connection after a hard monsoon season.

Which Linear Models This Applies To

Linear keypads and intercoms come in a few families, and the part numbers don’t cross over neatly. The most common driveway keypads in this area are the Linear AK-series (the AK-11 and its weatherproof siblings) and the older ACP-series access controls; the intercoms are the AM-series stations. Model numbers live on a label inside the housing or under the keypad cover, and on the older units that label is often the first thing to go after a few Nevada summers. If the label is unreadable, measure the post cutout and the keypad face and photograph the control board, and we can usually match the part from those.

Here’s the OEM-versus-aftermarket call for Linear specifically. For a keypad faceplate or a simple button pad, a quality aftermarket match works fine and saves money. For anything that talks to the control board, a genuine Linear replacement is the safer bet, because the signaling and the credentials have to line up exactly or you’ll chase a ghost failure for a month. We won’t swap a control-board-adjacent Linear part for a no-name equivalent and tell you it’s the same thing. We’ll tell you what to expect from the honest choice.

Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Signs Your Linear Keypad & Intercom Repair Is Failing

You don’t have to guess. Here’s what a failing Linear keypad or intercom actually looks like in Whitney.

  • The code stops working but the buttons light up. Usually a burned or worn button pad or a keypad that’s lost its memory after a board hiccup. The gate is fine; the reader is not.
  • You have to press the code twice, then three times. The keypad membrane is wearing out. As the contacts degrade, a fall in Whitney with its temperature swings makes an old membrane worse, not better.
  • The intercom is dead on the driveway side. A cut or wet station cable is the usual culprit, followed by a failed station speaker. Faded, water-logged box or a speaker that’s gone silent, either way it’s a part, not a mystery.
  • The gate responds on its own or not at all. A sticking keypad contact or a loose control-board connection. This one is worth a prompt call, because a gate that opens on its own is a security issue, not a convenience one.
  • The display fades, flickers, or shows nonsense. Moisture inside the keypad housing, or a power supply that’s sagging. Common after a long Whitney summer and the first cool nights that follow.

If you recognize two or more of these, the part is on its way out. One is a warning; two is a call.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Here’s the honest range for Whitney. The numbers are the price you’re quoted before any work starts, and they include the part and the labor.

Job Typical installed price What drives the range
Linear keypad replacement (same model, like-for-like) $185 – $240 Part family and post wiring condition
Linear keypad replacement with wiring repair $240 – $340 Cable run, post access, old terminations
Linear intercom station replacement $220 – $340 Station model, speaker cable, distance to gate
Keypad and intercom together, same visit $340 – $460 Shared post work and shared labor

A few things push a job to the top of a range: a control board that’s already failed and needs its inputs re-terminated, a keypad post that’s shifted out of plumb, and old wiring that should have been replaced a decade ago. None of that is a surprise line on the bill. We inspect first, quote a fixed price, and don’t add to it once you’ve agreed. Every job carries our 90-Day Done Right Promise, in writing: if the keypad or intercom we touched isn’t right, we come back and make it right. Active repairs over $250 also qualify for the $50 off standing offer.

DIY or Call Us?

Some of this an owner can check safely. Before you call, confirm the keypad has power (the lights tell you), look for water inside the housing, and check that the gate’s own control board has no error lights. That’s the safe list. Replacing a keypad or intercom station means working with low-voltage wiring at the post and, on some Linear units, at the control board. We don’t recommend hand-rigging a replacement keypad or intercom station into the control-board terminals unless you’re confident with the wiring: a crossed connection there can take out the board and turn a $200 part into a much bigger repair. The honest answer is that a straight part swap is safe to call us for, and the money you’d save doing it yourself doesn’t cover the risk. Call (855) 928-1304 and we’ll get it done right the first time, with the price settled up front.

FAQs

How long does a Linear keypad last in Whitney? In this climate, a Linear keypad typically lasts 6 to 10 years before the membrane and the weather seal give up, and a post that takes direct afternoon sun usually lands closer to 6. Intercom stations run about the same unless water gets in. If yours is in that range and starting to misbehave, replacing it now is cheaper than chasing a failure later.

Can my Linear keypad or intercom be repaired instead of replaced? Sometimes. A keypad whose membrane is still intact and whose failure is just a wiring termination or a board input can often be repaired, and an intercom with a wet connector is often a repair, not a replacement. If the button pad itself is worn through, replacement is the honest answer. We’ll tell you which one you’ve got after we test it, not before.

How long does the swap take? A like-for-like Linear keypad swap is typically 30 to 60 minutes. An intercom station or a keypad with wiring repair usually takes one to two hours, and a combined keypad-and-intercom job on the same post often runs a couple of hours. We do most jobs in a single visit because we’re trained and equipped on Linear and the brands around it: LiftMaster, Mighty Mule, and Ghost Controls too.

How do you source the right Linear part? We match your exact model and, where the label is gone, match from measurements and photos of the control board. We call the exact part number with you before we order, so there’s no guesswork and no wrong-model surprise on install day. Call (855) 928-1304 for a free estimate.

When your Linear keypad or intercom leaves you stranded at the driveway, the fix shouldn’t take a week. Call Ironworks Gate Co. Whitney at (855) 928-1304 for a free estimate, and we’ll test the part, quote a square price before any work starts, and back the repair with our written 90-Day Done Right Promise. A live person answers, day or night.

Written by the team at Ironworks Gate Co. Whitney, serving Whitney and nearby areas.

Need Gate Repair help nationwide? Licensed & insured · 1-hour response · free estimates
Call (855) 928-1304
Local Service Coverage

Request a Free Estimate in Whitney

Tell us what you need - Ironworks Gate Co. Whitney responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch