Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateLinear Gate Motor & Opener in Whitney: What to Know First
We provide independent Linear gate motor and opener service in Whitney, and most Linear repairs are finished in a single visit. A dead Linear slide or swing operator usually comes down to the control board, the limit switch, or the battery backup, and we diagnose all three before quoting a price. You’ll get an upfront number settled before a single bolt is turned, backed by our written 90-Day Done Right Promise. This page is for Whitney homeowners who already have a Linear unit on the driveway and want it working correctly, not replaced on a hunch. Call (855) 928-1304 and a live person picks up, day or night.
How Linear Products Fail – and How We Fix Them
Linear builds solid residential operators, and the Linear-branded units we see around Whitney tend to fail in predictable ways. Knowing the pattern saves you from paying for parts you don’t need.
- Control board failure on the Linear LSO/LS-series slide operators. The board is where most Linear slide motor problems start. A unit that runs a few inches and stops, or clicks but won’t move, is often a board that’s lost its programming after a power surge. We test the board under load and, when it’s the culprit, replace it with a Linear OEM board so the limit programming and remote codes carry over cleanly.
- Limit-switch drift on swing operators. Linear swing openers use mechanical limit switches, and after years of heat cycling the arm travel creeps until the gate over-travels or reverses halfway. The symptom is a gate that won’t fully close or bounces back. We reset the limits and check the arm geometry rather than just nudging the switch, because drift usually means a worn hinge or a sagging post is pushing the gate out of alignment.
- Battery backup that won’t hold. Linear battery-backup units in Whitney take a beating from summer heat, and a sealed battery that’s three or four years old will fail the moment the power drops. If your gate won’t open during an outage, the battery is the first thing we check, and we replace it with a correctly rated cell, not a generic one that fits the tray but not the charge profile.
- Gear and drive-train wear. On older Linear slide motors the drive gear and the chain or belt wear together, and the unit starts to sound labored or slip under load. We inspect the gearbox and the drive train together, since replacing one without the other just moves the failure down the line.
- Intercom and keypad wiring at the operator. When a Linear operator is paired with an intercom or a keypad, a loose low-voltage connection at the control board is a common reason the gate “won’t respond” even though the motor is fine. We trace the accessory wiring at the board before assuming the operator has failed.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Linear Gate Motor & Opener Process
Every Linear job follows the same path, from the first call to the final walk-through.
- 1
Diagnose on site. We test the motor, control board, limits, battery backup, and any intercom or keypad wiring, then tell you plainly what’s wrong.
- 2
Decide OEM versus aftermarket. We explain the trade-off and let you choose: a Linear OEM part for a warranty-safe, exact fit, or a quality aftermarket equivalent when it makes sense for the age of the unit. No surprises on the bill either way.
- 3
Repair. We make the fix with the gate secured and the power isolated, following the manufacturer’s procedure so nothing downstream is disturbed.
- 4
Test under real load. We cycle the gate open and closed multiple times, check the safety edges and reversal, and confirm the battery backup engages when power is cut.
- 5
Clean up and guarantee it. We leave the site as we found it and back the work with the written 90-Day Done Right Promise.
See the difference
Before
After
Before
After
Before
AfterWhat Linear Gate Motor & Opener Costs in Whitney
Linear gate motor and opener work in Whitney falls into a few realistic ranges. These are typical figures, and your exact price depends on the model and what we find on site.
| Scenario | Typical Range |
|---|---|
| Diagnostic visit and limit/battery reset | $95 – $150 |
| Battery backup replacement (Linear OEM cell) | $180 – $320 |
| Control board replacement (Linear LSO/LS series) | $350 – $650 |
| Gear / drive-train repair on slide motor | $300 – $600 |
| New Linear slide or swing motor installation | $1,200 – $2,400 |
What moves the price: the model series, whether the part is OEM or aftermarket, gate weight and travel on a slide unit, and whether accessory wiring needs redoing. We quote and agree the price before any work starts. Estimates are free, and ask about $50 Off Any Repair Over $250.
Why Whitney Homeowners Call Ironworks Gate Co. Whitney for Linear Work
We’re an independent Linear service provider, and we know these units from the inside out. Our technicians have up to 13 years of experience, and they’re trained and equipped across nine gate-automation brands, so if the fix turns out to be a different system than expected, we’re still the right call. A live person answers the phone 24 hours a day, every day, not a voicemail. Every job is covered by our written 90-Day Done Right Promise: if it isn’t right, we come back and make it right. Senior and Veteran 5% discount is standing. If you’ve weighed us against someone who handles only one brand, we also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing in Whitney. Call (855) 928-1304.
FAQs
Linear’s warranty depends on the model and its age, and we check that before choosing parts. As an independent Linear service provider we aren’t the manufacturer, but we use OEM parts and manufacturer procedures so a valid warranty stays intact. Call (855) 928-1304 and we’ll walk through what your unit qualifies for.
Yes for most current and recent Linear series. For discontinued models we source quality aftermarket equivalents and tell you plainly when that’s the better path, with pricing settled before work begins.
Repair when the motor and gearbox are sound and the fault is a board, limit, or battery; replace when the drive train is worn out or parts are no longer available. We diagnose on site and give you both numbers so the choice is yours. Call (855) 928-1304 for a free estimate.
Most Linear repairs are a single-visit job, and we answer the phone around the clock for gate emergencies. Call (855) 928-1304 and we’ll tell you the soonest we can be there.
Yes. Accessory wiring at the control board is a common cause of a gate that won’t respond, and we trace and repair it as part of the job. Call (855) 928-1304 for a free estimate.
Written by the team at Ironworks Gate Co. Whitney, serving Whitney and nearby areas.