Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGhost Controls Welding & Fabrication: The Whitney Owner’s Guide
We handle Ghost Controls welding and fabrication work for Whitney homeowners, and a typical fabricated bracket, hinge repair, or weld-on post mount runs $210 to $560 installed, with most repair calls completed in a single visit. Gate frames bend, hinge weld plates fatigue, and mount arms crack loose over Nevada summers, and that’s usually how the problem shows up: the gate drags on the drive, the arm kicks sideways under load, or the opener strains and reverses partway through travel. If your Ghost Controls operator is working but the metal around it isn’t holding, the automation isn’t your problem – the fabrication is. We’re an independent service provider, not affiliated with Ghost Controls, and we’ve worked on their arms, mounting hardware, and gate frames across the Whitney area enough to know exactly where their assemblies give out first.
Which Ghost Controls Models This Applies To
Ghost Controls builds primarily for swing gates with their TSS, TDS, and heavier HDP series, and the fabrication work attaches to the gate arm bracket, the operator’s rear post mount, and the hinge plates themselves rather than to the control head. The first thing we look for is the model label on the underside of the operator housing and the arm label at the joint, because the arm bracket geometry and the post-mount bolt pattern shift between series. The compatibility gotcha most Whitney owners hit: a bracket that fits a TSS arm will not mate cleanly to an HDP arm, and a fabricator who welds a one-size mount to the post leaves you with an arm angled wrong, binding at the last eighteen inches of travel. We measure the arm-to-post geometry and the gate’s actual swing arc before any metal is cut. On the OEM-versus-aftermarket question, we source a Ghost Controls-compatible bracket or arm mount when the factory geometry matters and a properly steeled, correctly gauged fabricated part when the original design is what failed in the first place. A fabricated mount built from the right gauge steel in the right shape outlasts a stamped replacement in most cases, but only when it’s measured to your gate, not bent to guesswork.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Ghost Controls Welding & Fabrication Is Failing
- The arm binds or the gate stalls mid-travel. That usually means the post-mount bracket has bent or the weld plate has fatigued, throwing the arm out of alignment. The opener reads the resistance and trips the safety reverse.
- Visible cracks at the hinge or mount weld. Heat cycles and a sagging gate load the weld until it stress-cracks. By the time you see the crack, the plate has shifted.
- The gate sags and the operator strains to push it. A fatigued hinge weld or a bent frame lets the gate drop, and the Ghost Controls arm fights the bind on every cycle. Left alone, that shortens motor life.
- Rattling or clunking from the operator bracket during travel. Loose or elongated bolt holes in a worn or undersized bracket let the arm move under load. This one gets worse fast in summer heat.
- The opener runs but the gate barely moves, or reverses on its own. A fabrication that has pushed the arm past its correct angle makes the operator work against the geometry. That’s not an operator fault, and replacing the head won’t fix it.
Nevada’s dry heat and summer sun work against steel and welds. Metal expands and contracts through the day, and after a decade a gate frame around a Whitney driveway will tell you about every loose weld in the assembly. When we get on site, we find the failed joint and check the ones beside it, because the next weld is usually standing in line behind the first.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Fabrication and weld repair for a Ghost Controls gate setup in Whitney falls into a few honest ranges. Straight weld repair or re-welding an existing mount runs around $210 to $340. A fabricated replacement bracket or a rebuilt hinge area is roughly $280 to $440. A fabricated post mount or arm-mount rebuild, including realignment to the operator, sits near $380 to $560. What drives the range is the metal work itself: how much cutting and fitting the geometry needs, whether we fabricate a new part or repair the original, and how far the gate has to be cleared to get at the weld. Parts and labor are quoted separately up front. We settle the price with you and agree on it before a single bolt is turned, and you won’t find a surprise on the bill. Every fabrication job carries our 90-Day Done Right Promise: written, no paperwork, no arguing. If we didn’t get it right, we come back and make it right.
DIY or Call Us?
There’s a little you can safely check yourself. Walk the gate, push it to half-travel, and look for a bind. Run the operator and watch where the arm angles as it moves. Look at the hinge plates and the mount bracket for visible cracks or elongation. What you shouldn’t do is try to weld or fabricate the mount or hinge area yourself. The arm bracket and hinge welds carry the full push-pull load of a moving gate, and a weak weld in the wrong place means a gate that drops or swings free under the operator, which is a serious injury risk for anyone nearby. Metal fabricating at this load and wear point is a job for someone who measures the geometry, preps the surface correctly, and trusts the weld. We’re equipped for exactly that, and we’re a phone call away at (855) 928-1304.
FAQs
A properly fabricated bracket or weld in Whitney’s climate should hold a decade or more when it’s built from the right gauge steel and the gate isn’t sagging against it. Factory-stamped mounts often go first because they’re thinner and lose their shape when the gate shifts. Prep and correct geometry add the years.
Often, yes. A stress crack in a sound bracket can usually be re-welded and reinforced if the metal hasn’t fatigued through. If the part has bent out of geometry, we fabricate a replacement, because straightening a fatigued bracket just delays the next failure.
Most weld repair and bracket jobs run one to three hours on site, and we complete most in a single visit. A full post-mount rebuild that needs custom fabrication can take longer, and we tell you the timeline before we start.
We match the part to your Ghost Controls series first, from the model label on the operator and the measurements off the gate. With that, we either fabricate a correctly gauged replacement or source a Ghost Controls-compatible part that fits. We don’t stock parts and nothing is carried on a truck, so we confirm fit before ordering, and the price is agreed before any work starts. Call (855) 928-1304 for a free estimate.
We also service LiftMaster, Mighty Mule, and DoorKing on the same visit, so whichever opener is on your drive, we come prepared. If your Ghost Controls gate is fighting the metal instead of the motor, let us look at it. We’re proud to serve Whitney and nearby areas, background-checked and uniformed on every job, and we stand behind what we do. Call Ironworks Gate Co. Whitney at (855) 928-1304 for a free estimate and a straight answer.
Written by the team at Ironworks Gate Co. Whitney, serving Whitney and nearby areas.