A Ironworks company - serving Whitney, NV

Ghost Controls Keypad & Intercom Repair in Whitney, NV

Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

Ghost Controls Keypad & Intercom Repair: The Whitney Owner’s Guide

Ghost Controls keypad and intercom repair in Whitney runs $185 to $420 installed, and most keypad failures can be handled within a day of your call. We match the part to your model, quote the price upfront, and settle the bill before any work starts. The intercom side – the audio unit that lets a visitor talk to the house – adds cost when the unit itself has to be replaced rather than rewired.

Call (855) 928-1304

Owners in Whitney usually discover the problem the same way: the code that worked for years stops taking, or the gate opens for a neighbor’s code but not their own. Others notice the intercom crackles, cuts out, or the visitor hears only static. In older neighborhoods off Whitney Ranch Parkway and near the McCullough Range foothills, we see heat-worn keypad buttons and sun-cracked housings more than anything electrical.

Key Takeaways

  • Installed keypad repair: $185 – $320. Intercom repair or replacement: $240 – $420.
  • We service Ghost Controls alongside LiftMaster, Mighty Mule, and DoorKing.
  • We are an independent service provider, not affiliated with Ghost Controls.
  • Every job is covered by our written 90-Day Done Right Promise.

Which Ghost Controls Models This Applies To

Ghost Controls builds its residential automation around the TSS1, TDS2, and similar single and dual-gate operator families, and most of them use the same accessory keypad protocol. The wireless keypad sold for these systems typically carries an “AX” or “AR” prefix on the model label, and the intercom units pair to the operator through a matched receiver. The first thing we do on a Whitney call is read the label inside the operator housing and on the keypad back plate. That tells us the series and the pairing method – which matters, because a keypad built for one protocol will sometimes accept a code and then fail to transmit it, and the owner assumes the keypad is dead when the mismatch is the real problem.

You have a real choice between the OEM Ghost Controls replacement and a quality aftermarket equivalent. The OEM part matches your existing mount and pairs the way the original did. Aftermarket keypads are often less expensive and can be more weather-sealed for desert conditions, but the pairing steps differ and mounting holes rarely line up exactly. If your gate operator is still under its factory warranty, we run the OEM route so nothing gets voided. When the operator is older, the aftermarket option is worth pricing – we show both numbers and let you decide.

Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Signs Your Ghost Controls Keypad & Intercom Repair Is Failing

Here is what a failing unit looks like, and what is usually behind it:

  • Codes stop registering. The keypad accepts the digits but the gate does not move. Most often the keypad’s memory has lost its pairing with the operator receiver, or the battery in a wireless unit is failing under load.
  • Buttons feel soft or mush. Heat and UV in the Whitney sun break down the rubber membrane over time. A button that no longer clicks is a button that no longer makes contact, and no amount of pressing harder fixes it.
  • The intercom crackles or cuts out. Moisture in the handset or a loose wire at the gate post terminal. Dust intrusion is common here; the desert air finds every gap.
  • Visitor hears static but you hear fine. That is a speaker or microphone element on the outside unit, not a house-side problem. It is a common failure after a few summers.
  • Gate opens for some codes but not others. A partial memory corruption in the keypad, or an older code that was never fully cleared. We read the stored codes before touching anything.

Two seasons of Whitney heat will test any outdoor keypad. We see the same pattern on gates facing west toward the McCullough Range foothills – the sun does more damage than rain ever will.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Installed pricing for Whitney homeowners runs like this:

Service Typical installed range
Wireless keypad repair (re-pair, rewire, or reset) $185 – $260
Keypad replacement (part plus labor) $240 – $320
Intercom repair (rewire, handset, or element) $240 – $340
Intercom replacement (part plus labor) $320 – $420
Combined keypad and intercom service call $350 – $520

What drives the range: whether the unit is wired or wireless, whether the controller has to be re-paired across a longer wire run, and whether the part is OEM or an approved aftermarket equivalent. Gate posts vary in how much room they leave for a clean mount, and a post that needs a small weld or bracket repair adds to the job.

You get a written price before a single screw turns. The part, the labor, the clean-up, and our 90-Day Done Right Promise all sit under one number. If the fix is not right, we come back – no paperwork, no arguing, no exceptions. Current offer: $50 off any repair over $250, and a free second opinion on any written estimate you have.

DIY or Call Us?

You can safely do a few things. Check that the operator still works from the inside remote – if it does, the keypad is the problem. Replace the batteries in a wireless keypad. Look at the keypad face for cracks or a loose mount. Wipe the contacts and the buttons clean. None of that will hurt anything.

Do not open the operator housing or the gate post wiring, and do not test a live circuit with anything but a proper meter. The 12-volt accessory line and the 120-volt feed into the operator sit in the same box on some installs, and a Whitney homeowner working blind in that box can get a bad shock. Intercom wiring runs at low voltage but it runs through the ground where it can pick up moisture, and tracing it takes a meter and time. This is not the part to learn on. Call Ironworks Gate Co. Whitney at (855) 928-1304 and we will tell you straight whether a repair or a replacement makes sense for your gate.

FAQs

Need Gate Repair help nationwide? Licensed & insured · 1-hour response · free estimates
Call (855) 928-1304
Local Service Coverage

Request a Free Estimate in Whitney

Tell us what you need - Ironworks Gate Co. Whitney responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch