A Ironworks company - serving Whitney, NV

Ghost Controls Gate Motor Replacement in Whitney, NV

Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

Ghost Controls Gate Motor Replacement: The Whitney Owner’s Guide

We replace Ghost Controls gate motors in Whitney, and the installed price typically runs $650 to $1,100 depending on which unit you have and how much of the assembly needs to come out. Most replacements are handled on a single visit with upfront pricing agreed before we touch a bolt. Owners usually find their way to us the same way: the arm starts stalling halfway through an open cycle, or it hums and gives up, or the gate reverses on its own after a stiff Las Vegas Valley wind. By the time the control board starts blinking a fault code they can’t clear, the motor is usually the answer.

Call (855) 928-1304

Which Ghost Controls Models This Applies To

Ghost Controls sells its residential units as system kits (single or dual gate, in the box with the arm, operator, control board, battery and solar option) rather than under one fixed model name, and Whitney owners most often have a single-gate kit from the heavy-duty arm family. The first step is always the nameplate on the arm housing or the control board inside the operator, not the manual you found in the drawer. That label carries the arm length and the torque rating, and those two numbers decide what fits.

The gotcha we see on nearly every Whitney visit: a kit bought for a lighter gate gets swapped onto a heavier one during a previous repair and the arm burns out early every time. If the gate leaf has been rehung, widened, or had a board added since the original install, the original motor spec may already be the wrong one. We measure the leaf, check the rating, then match.

On the OEM-versus-aftermarket question for Ghost Controls specifically: genuine parts carry a known rating and warranty, and a fair number of aftermarket arms claim compatibility but run a different gearset. We’ll tell you plainly which is which, quote both, and let you decide. Ironworks Gate Co. Whitney is an independent service provider and not affiliated with Ghost Controls. We also service LiftMaster, Mighty Mule, and DoorKing.

Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Signs Your Ghost Controls Gate Motor Replacement Is Failing

The pattern is usually slow before it’s sudden. These are the symptoms we diagnose most often in Whitney:

  • Stalling halfway through the cycle. The motor can’t push through the mid-point resistance. A worn gearset or a leaf that has drifted out of alignment is the cause, and it gets worse as the gate binds further.
  • Constant fault codes on the control board. Flashing codes usually mean the arm traveled outside its stall limits. A few of those are the board misreading a tired motor.
  • Motor strains and labors but doesn’t move the gate. The gearset or the arm is done. Ghost Controls arms in single-gate kits typically wear out well before a Whitney homeowner expects, often within 5 to 7 years on a gate that sees daily use.
  • Reversal on any pressure. The operator signals it needs retorque or a new arm. A gust the operator can’t read will trip the safety reversal and stop the gate mid-open.
  • Bad or intermittent battery with a solar setup. Solar-charged systems in the Nevada heat lose battery capacity fast. A week of 105-degree days flattens a weak battery and the operator won’t run the arm. This one is often fixed without a new motor.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Installed pricing in Whitney breaks down roughly like this:

Scope Typical Installed Range
Single-gate motor replacement, standard residential $650 – $950
Single-gate motor replacement, heavy-duty arm or more complex install $950 – $1,100
Battery or solar charge accessory replacement only $150 – $300

What drives the range: the arm’s torque rating, whether both gate leaves need service, whether wiring or the control board needs work, and whether the existing bracket setup is salvageable. Parts and labor are itemized separately. Upfront pricing is quoted and settled before any work starts, so you know the number. Every repair carries the 90-Day Done Right Promise: if it isn’t right, we come back and make it right. Current offer: $50 off any repair over $250.

DIY or Call Us?

What you can safely check yourself: whether the control board is powered, whether the battery is holding charge, whether the gate leaf swings free with the arm disconnected, and whether the nameplate on the arm is legible. Those checks save us time and can sometimes rule out a bad board instead of a bad motor.

Where DIY goes wrong for this part: a gate arm carries stored tension, and a wrong-size replacement strain the gate’s hinge or the operator’s gearing. The bigger risk is the 110-volt power run to the operator and the gate’s safety reversal edges. Wiring that back wrong, or leaving the safety edges untested, can leave you with a gate that closes on a car or a person. We handle the electrical properly. If you want the swap done right the first time in Whitney, call (855) 928-1304 for a free estimate.

FAQs

Need Gate Repair help nationwide? Licensed & insured · 1-hour response · free estimates
Call (855) 928-1304
Local Service Coverage

Request a Free Estimate in Whitney

Tell us what you need - Ironworks Gate Co. Whitney responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch