A Ironworks company - serving Whitney, NV

FAAC Gate Parts & Welding in Whitney, NV

Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

FAAC Gate Parts & Welding in Whitney: What to Know First

We provide independent FAAC gate parts and welding in Whitney, and most jobs are finished in a single visit once the correct part is on hand. Simple hinge, roller, and latch work is often same-day; custom welding or a post replacement may take a few days to schedule. You get an upfront price before we touch the gate, and it doesn’t change on the bill.

Call (855) 928-1304

This page is for the Whitney homeowner with a FAAC operator on the driveway – a 400 series, an S800H, a 770, a C721 – that has started to drag, sag, or fail to latch. We’re an independent FAAC service provider, meaning we’re not affiliated with or authorized by FAAC. If that’s you, call (855) 928-1304 and a live person will pick up, day or night.

How FAAC Products Fail – and How We Fix Them

FAAC builds a solid operator, but the steel that carries it takes the beating. In Whitney, the desert heat and dry air work on hinges, posts, and welds in ways that inland coastal owners never see. These are the failures we run into most on FAAC systems.

  • Sagging hinges on a swing gate. The pivot hinges on FAAC 400 and 390 swing operators wear under the constant push-pull of an automated leaf, and dry Whitney summers speed it up. A leaf that drags on the ground or won’t close flush is usually hinges, not the motor. We replace worn hinges and re-hang the leaf square.
  • Loose or cracking hinge post. The post takes the full weight and torque of an automated swing gate, and when the concrete footing was set shallow it works loose over the years. We reset or replace the post – not just weld a patch over the crack – so the operator arm lines up and the gate stops fighting itself.
  • Rail and frame fatigue at the weld joints. Long gate leaves on a FAAC swing system flex slightly every cycle, and the weld at the rail-to-frame corner is where the crack starts. We cut out the failed joint and re-weld it properly rather than stacking a cosmetic bead on top.
  • Rollers and guide wear on sliding gates. FAAC sliding operators like the 770 and C721 push a heavy leaf, and a flat or seized roller loads the motor and strains the track. When the gate stutters or the operator strains, the rollers are usually the cause. We swap the rollers and true up the track.
  • Latch and lock misalignment. Once a hinge sags or a post shifts even a quarter inch, the latch and lock no longer line up, and the gate rattles or won’t secure. We align the hardware to the corrected gate rather than forcing the mechanism to compensate for a gate that’s out of square.
Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Our FAAC Gate Parts & Welding Process

Every FAAC job follows the same steps, whether it’s a single hinge or a full post reset.

  1. 1
    Diagnose on site. We test the operator, check the leaf for square, examine the hinges, rollers, post, and welds, and trace the failure to its source – not just the symptom.
  2. 2
    Decide on parts. We’ll tell you honestly whether OEM FAAC parts or a quality aftermarket equivalent is the right call for your model, and what each costs. On automation components we lean toward OEM to keep the warranty intact; on structural steel and hinges, a quality aftermarket part often serves better.
  3. 3
    Quote before we start. You get the price in writing and agree to it before a single bolt is turned.
  4. 4
    Do the repair. Replace the parts, cut out failed welds and re-weld, reset the post if needed, and re-hang the leaf square.
  5. 5
    Test the full cycle. We run the gate through multiple open-and-close cycles, check the safety edges and alignment, and confirm the latch and lock engage cleanly.
  6. 6
    Back it in writing. Every job carries our 90-Day Done Right Promise – if it isn’t right, we come back and make it right.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

What FAAC Gate Parts & Welding Costs in Whitney

Every FAAC job is quoted upfront, so you know the number before we start. Here’s a realistic range for common scenarios.

Job Typical range
Hinge replacement (per hinge) $150-$350
Gate roller replacement (set) $180-$400
Latch and lock realignment or replacement $120-$280
Rail or frame weld repair $200-$500
Post replacement (reset footing) $600-$1,400
Custom welding / fabrication $250-$900

What moves the price: gate weight and leaf size, whether the post footing has to be reset, OEM versus aftermarket parts, and how much welding is involved. Estimates are free – call (855) 928-1304 for an exact number on your FAAC gate.

Why Whitney Homeowners Call Ironworks Gate Co. Whitney for FAAC Work

Most of our Whitney customers have lived in their home twenty years or more and have been let down by a contractor before. They want the job done once. Our technicians have up to 13 years of experience, and they’re trained on FAAC alongside eight other major brands – LiftMaster, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule – so the correct fix is made on the first visit. A live person answers the phone 24 hours a day. Every job is backed by our written 90-Day Done Right Promise. And we bring standing offers worth knowing: $50 off any repair over $250, a free second opinion on any written estimate, an $89 seasonal tune-up, and a permanent 5% senior and veteran discount. We stand behind it – and back it in writing.

FAQs

Need Gate Repair help nationwide? Licensed & insured · 1-hour response · free estimates
Call (855) 928-1304
Local Service Coverage

Request a Free Estimate in Whitney

Tell us what you need - Ironworks Gate Co. Whitney responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch