Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFAAC Gate Motor Replacement: The Whitney Owner’s Guide
FAAC gate motor replacement in Whitney costs most homeowners between $650 and $1,450 installed, depending on the swing or slide model and how much of the original hardware survives the swap. We replace FAAC motors for Whitney homeowners, and most jobs are completed in a single visit with the price settled before we start. You usually find out the motor is done the same way everyone does: the gate stops mid-travel, or it groans, or it opens two feet and gives up. Sometimes the arm is fine and the control board is heat-soaked from a Las Vegas Valley summer. Either way, the gate quits, and the driveway stops working the way it has for years.
Which FAAC Models This Applies To
FAAC builds two families of residential driveway operators, and the replacement path differs for each. Swing operators run the 400, 390, 391, 740, and 770 series, plus the S800 and C720 lines. Slide operators run the 844, 860, and 884 series, along with the older 750. FAAC operators share a naming logic that helps: a 391 and a 390 look almost identical, but the board and the encoder can differ, and that matters when you’re matching a replacement.
Find the model plate before you buy anything. On swing arms it sits on the underside of the casing or inside the cover, and it lists the series and the voltage (120V on almost all US-spec FAAC gates). On slide operators the plate is on the motor housing, and it includes the rated thrust. Write down the series, voltage, and any suffix like “CBAC” or “800.” Then measure. A 400-series arm is not the same length as a 770, and a slide operator sized for a 1,200-pound gate will not carry a 2,400-pound gate just because the bolt holes line up.
One compatibility gotcha worth knowing in Whitney: FAAC changed encoder and limit-switch logic partway through the 390 and 740 runs. A late board will not accept an early arm’s encoder, and mixing them throws a limit fault that looks like a motor failure. If your arm is stamped with a different lot code than your board, we check both before quoting a replacement. Alongside FAAC, we also service LiftMaster, Mighty Mule, and Ghost Controls, so the brand on your driveway is not a roadblock.
On the OEM question: a genuine FAAC arm or board is the safe match, and for most Whitney homeowners it is the right call. A quality aftermarket equivalent exists for some FAAC swing arms and control boards, and it can cut $100 to $250 from the bill. We tell you plainly which parts have a sound aftermarket option and which do not. FAAC slide operators in particular are better served by genuine parts. Ironworks Gate Co. Whitney is an independent service provider and is not affiliated with FAAC.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your FAAC Gate Motor Replacement Is Failing
- Gate reverses or stops partway. The motor loses torque or the encoder misreads position, so the board thinks the gate hit an obstacle. In Whitney, this often shows up first on the afternoon sun side of the driveway, when a motor that ran cool all winter heats past its duty rating.
- Loud grinding or a metallic scrape. The gearbox or the drive nut has worn, and metal is running on metal. This one gets worse fast and usually means the whole motor assembly, not just a gear set.
- Arm moves but the gate doesn’t. The linkage pin, the arm bracket, or the gate’s own hinge has failed. Sometimes the motor is fine and the gate is the problem, which is why we look at the whole assembly before quoting a replacement.
- Clicking at the control board, no movement. The board, capacitor, or transformer has failed. A dead capacitor looks exactly like a dead motor to most owners, and it is a fraction of the price to fix.
- Tripping the breaker or the GFCI. A shorted winding or water intrusion in the motor housing. In the Las Vegas Valley, monsoon-season rain and dust combine to wear motor seals, and a Whitney motor that ran fine through a dry spring can fault out after the first hard summer storm.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here is the honest range for Whitney, quoted and agreed before a single bolt is turned:
- Swing arm replacement (400, 390, 740, 770 series): $650 – $1,050 installed
- Slide operator replacement (844, 860, 884 series): $900 – $1,450 installed
- Control board only: $275 – $475 installed
- Capacitor or limit switch only: $140 – $260 installed
- Aftermarket equivalent, where sound: $100 – $250 less than OEM
The price includes removal of the old operator, mounting, wiring, limit and force adjustment, and a full cycle test. What drives the range: gate weight, whether the mounting plate or arm bracket needs rework, and whether the wiring is sound. Every job is backed by our 90-Day Done Right Promise, and we stand behind it.
DIY or Call Us?
Some checks are safe. You can read the model plate, confirm the breaker is on, clear debris from the gate’s path, and check whether the gate swings freely by hand with the operator disengaged. Those tell you whether the problem is the gate or the motor, and they cost nothing.
Where DIY goes wrong: motor replacement means working inside a 120V circuit, disconnecting line power, and re-tuning force and limit settings for a specific gate weight. Get the force setting wrong and the gate will not reverse on an obstruction, which is a real hazard for anyone in the driveway. On slide operators, the drive gear and chain carry load, and a mistake there can damage the gate or the operator. We do not hand out step-by-step instructions for that work, and we would rather you call than get hurt. A free second opinion on any written estimate is one call away at (855) 928-1304.
FAQs
Seven to twelve years is realistic for a FAAC operator in this climate, and heat is the main driver. Whitney summers push motors past their duty rating, and a motor rated for a lighter gate wears out years sooner than one sized correctly. We see a lot of FAAC arms fail their first hard summer after a dusty spring, once the seals give and grit gets into the gear.
Often, yes. A failed capacitor, limit switch, or control board is a repair, not a replacement, and it is $140 to $475 installed rather than $650 to $1,450. A worn gearbox or a shorted winding usually means replacement. We test the parts before recommending either path, so you are not buying a motor you don’t need.
Most Whitney swaps are done in a single visit, three to five hours for a swing arm and four to six for a slide operator. Mounting plate changes and wiring repairs add time. We settle the price first and will be there when we say.
We match the part to the model plate and the lot code, then confirm fit against the gate’s weight and travel before ordering. We source genuine FAAC parts and quality aftermarket equivalents where they are sound. We do not claim to stock parts or carry them on a truck, so the correct part is ordered for your gate and confirmed before we arrive.
FAAC gate motor replacement does not have to be a gamble. A square deal, done right, and backed in writing is the way we work every Whitney job. Call Ironworks Gate Co. Whitney at (855) 928-1304 for a free estimate.
Written by the team at Ironworks Gate Co. Whitney, serving Whitney and nearby areas.