A Ironworks company - serving Whitney, NV

Before & After Gallery - Ironworks Gate Co. Whitney

Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

Gate Repair Before & After in Whitney, NV

Pictures settle arguments that words can’t. A sagging gate that drags on the concrete, a keypad that quit in the heat, a weld that split after a monsoon gust – these are the things Whitney homeowners actually call us about. Below you’ll find the kinds of gate repair jobs we run here, described honestly and organized by the problem, so you can spot your own gate in one of them. The photo slots are ready for our crews to fill in as jobs are documented.

Call (855) 928-1304

Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Recent Transformations

Double Driveway Gate Repair – Sagging, Dragging, and Hard to Latch

Gallery image: before – a steel double-swing driveway gate visibly sagging on the trail edge, dragging the ground; after – the same gate level, squared, and closing cleanly at the center latch.

The problem: A steel double-swing gate on a Whitney property had dropped on its hinge side over years of heat cycling. The trail edge scraped the concrete every time it opened, and the two leaves no longer met at the center, so the latch missed unless someone lifted the gate by hand. What we did: We reset the hinge posts, replaced the worn hinge hardware, re-squared both leaves, and welded the split at the center stile. The result: The gate swings level, latches on the first try, and clears the ground again. The homeowner stopped parking to drag it closed.

Gate Motor Repair – Operator Stalled in the Afternoon Heat

Gallery image: before – a sliding gate operator housing open with a stalled motor and worn drive components visible; after – the same housing reassembled with fresh hardware and a smooth test cycle.

The problem: A sliding gate operator would run fine in the morning and stall partway through the afternoon, stranding the homeowner’s car inside the driveway. The cause was a combination of worn drive components and heat-thinned lubrication, not a dead motor. What we did: We serviced the drive train, replaced the worn parts, set the limits, and cycled the gate repeatedly to confirm it held through the heat of the day. The result: The gate opens and closes on demand at any hour, and the motor no longer labors near the end of its travel.

Gate Access Control Repair – Keypad That Quit Accepting Codes

Gallery image: before – a tired pedestal-mounted keypad with a cracked faceplate; after – a clean re-terminated keypad and pedestal with fresh seals.

The problem: A pedestal keypad at the entry had stopped accepting valid codes. The culprit was moisture that had worked into the wiring and a faceplate cracked by sun exposure, not a programming error. What we did: We re-terminated the low-voltage connections, sealed the pedestal against dust and rain, swapped the faceplate, and re-tested every code on the account. The result: Every household code works again and the keypad is protected from the next round of weather. We handle access control for the brands that come up most here, including DoorKing and LiftMaster systems.

Gate Welding Repair – Broken Weld on a Decorative Estate Gate

Gallery image: before – a decorative steel estate gate with a failed weld at a horizontal rail; after – the joint dressed, re-welded, and finished to match the surrounding steel.

The problem: A decorative steel estate gate had a failed weld where a horizontal rail met a picket, letting the leaf wobble and lean. Left alone, one broken weld on a gate that size tends to take its neighbors with it. What we did: We braced the leaf, cut out the failed joint, re-welded it to full penetration, and dressed and finished the repair so it reads as part of the gate. We checked the other joints while we were there. The result: The leaf hangs straight again and the gate no longer rocks in the wind.

Gate Roller and Track Repair – Sliding Gate That Jumped the Track

Gallery image: before – a sliding gate off its track with flattened rollers and a worn guide; after – the gate re-seated on new rollers with a level, cleared runway.

The problem: A residential sliding gate had jumped its track and would no longer travel in a straight line. The rollers were flat-spotted and the ground guide was worn, so the gate wandered as it rolled. What we did: We re-seated the gate on new rollers, replaced the guide, cleared the runway of debris, and adjusted the stops so the gate travels true from end to end. The result: The gate rolls smoothly under hand and motor power and stays on track through its full travel.

Gate Parts and Hardware Repair – Rusted Hinges and a Latch That Wouldn’t Catch

Gallery image: before – corroded hinges and a misaligned latch on a backyard pedestrian gate; after – new hinges and a latch that engages cleanly on the first push.

The problem: A pedestrian gate at the side of a house had rusted hinges and a latch that needed to be jiggled into place. The gate had dropped just enough to throw the latch out of alignment. What we did: We replaced the hinge set, shimmed the gate back to level, and reset the latch so it engages with one push. The result: The gate swings easily and latches on the first try. Small hardware fixes like this are often the difference between a gate you trust and one you fight.

Want Results Like These?

These are the gate repair jobs we take on across Whitney, NV – sagging leaves, stalled motors, dead keypads, broken welds, and worn hardware. Every job is quoted upfront before a single bolt is turned, and every repair is backed by our written 90-Day Done Right Promise. Call (855) 928-1304 to describe your gate and get a straight answer.

Written by the team at Ironworks Gate Co.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade
Need Gate Repair help in Whitney? Licensed & insured · 1-hour response · free estimates
Call (855) 928-1304
Local Service Coverage

Request a Free Estimate in Whitney

Tell us what you need - Ironworks Gate Co. Whitney responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch