A Ironworks company - serving Whitney, NV

Ghost Controls Welding & Fabrication in Whitney, NV

Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

Ghost Controls Welding & Fabrication: The Whitney Owner’s Guide

We handle Ghost Controls welding and fabrication work for Whitney homeowners, and a typical fabricated bracket, hinge repair, or weld-on post mount runs $210 to $560 installed, with most repair calls completed in a single visit. Gate frames bend, hinge weld plates fatigue, and mount arms crack loose over Nevada summers, and that’s usually how the problem shows up: the gate drags on the drive, the arm kicks sideways under load, or the opener strains and reverses partway through travel. If your Ghost Controls operator is working but the metal around it isn’t holding, the automation isn’t your problem – the fabrication is. We’re an independent service provider, not affiliated with Ghost Controls, and we’ve worked on their arms, mounting hardware, and gate frames across the Whitney area enough to know exactly where their assemblies give out first.

Call (855) 928-1304

Which Ghost Controls Models This Applies To

Ghost Controls builds primarily for swing gates with their TSS, TDS, and heavier HDP series, and the fabrication work attaches to the gate arm bracket, the operator’s rear post mount, and the hinge plates themselves rather than to the control head. The first thing we look for is the model label on the underside of the operator housing and the arm label at the joint, because the arm bracket geometry and the post-mount bolt pattern shift between series. The compatibility gotcha most Whitney owners hit: a bracket that fits a TSS arm will not mate cleanly to an HDP arm, and a fabricator who welds a one-size mount to the post leaves you with an arm angled wrong, binding at the last eighteen inches of travel. We measure the arm-to-post geometry and the gate’s actual swing arc before any metal is cut. On the OEM-versus-aftermarket question, we source a Ghost Controls-compatible bracket or arm mount when the factory geometry matters and a properly steeled, correctly gauged fabricated part when the original design is what failed in the first place. A fabricated mount built from the right gauge steel in the right shape outlasts a stamped replacement in most cases, but only when it’s measured to your gate, not bent to guesswork.

Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Signs Your Ghost Controls Welding & Fabrication Is Failing

  • The arm binds or the gate stalls mid-travel. That usually means the post-mount bracket has bent or the weld plate has fatigued, throwing the arm out of alignment. The opener reads the resistance and trips the safety reverse.
  • Visible cracks at the hinge or mount weld. Heat cycles and a sagging gate load the weld until it stress-cracks. By the time you see the crack, the plate has shifted.
  • The gate sags and the operator strains to push it. A fatigued hinge weld or a bent frame lets the gate drop, and the Ghost Controls arm fights the bind on every cycle. Left alone, that shortens motor life.
  • Rattling or clunking from the operator bracket during travel. Loose or elongated bolt holes in a worn or undersized bracket let the arm move under load. This one gets worse fast in summer heat.
  • The opener runs but the gate barely moves, or reverses on its own. A fabrication that has pushed the arm past its correct angle makes the operator work against the geometry. That’s not an operator fault, and replacing the head won’t fix it.

Nevada’s dry heat and summer sun work against steel and welds. Metal expands and contracts through the day, and after a decade a gate frame around a Whitney driveway will tell you about every loose weld in the assembly. When we get on site, we find the failed joint and check the ones beside it, because the next weld is usually standing in line behind the first.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Fabrication and weld repair for a Ghost Controls gate setup in Whitney falls into a few honest ranges. Straight weld repair or re-welding an existing mount runs around $210 to $340. A fabricated replacement bracket or a rebuilt hinge area is roughly $280 to $440. A fabricated post mount or arm-mount rebuild, including realignment to the operator, sits near $380 to $560. What drives the range is the metal work itself: how much cutting and fitting the geometry needs, whether we fabricate a new part or repair the original, and how far the gate has to be cleared to get at the weld. Parts and labor are quoted separately up front. We settle the price with you and agree on it before a single bolt is turned, and you won’t find a surprise on the bill. Every fabrication job carries our 90-Day Done Right Promise: written, no paperwork, no arguing. If we didn’t get it right, we come back and make it right.

DIY or Call Us?

There’s a little you can safely check yourself. Walk the gate, push it to half-travel, and look for a bind. Run the operator and watch where the arm angles as it moves. Look at the hinge plates and the mount bracket for visible cracks or elongation. What you shouldn’t do is try to weld or fabricate the mount or hinge area yourself. The arm bracket and hinge welds carry the full push-pull load of a moving gate, and a weak weld in the wrong place means a gate that drops or swings free under the operator, which is a serious injury risk for anyone nearby. Metal fabricating at this load and wear point is a job for someone who measures the geometry, preps the surface correctly, and trusts the weld. We’re equipped for exactly that, and we’re a phone call away at (855) 928-1304.

FAQs

Need Gate Repair help nationwide? Licensed & insured · 1-hour response · free estimates
Call (855) 928-1304
Local Service Coverage

Request a Free Estimate in Whitney

Tell us what you need - Ironworks Gate Co. Whitney responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch