Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGhost Controls Gate Motor Replacement: The Whitney Owner’s Guide
We replace Ghost Controls gate motors in Whitney, and the installed price typically runs $650 to $1,100 depending on which unit you have and how much of the assembly needs to come out. Most replacements are handled on a single visit with upfront pricing agreed before we touch a bolt. Owners usually find their way to us the same way: the arm starts stalling halfway through an open cycle, or it hums and gives up, or the gate reverses on its own after a stiff Las Vegas Valley wind. By the time the control board starts blinking a fault code they can’t clear, the motor is usually the answer.
Which Ghost Controls Models This Applies To
Ghost Controls sells its residential units as system kits (single or dual gate, in the box with the arm, operator, control board, battery and solar option) rather than under one fixed model name, and Whitney owners most often have a single-gate kit from the heavy-duty arm family. The first step is always the nameplate on the arm housing or the control board inside the operator, not the manual you found in the drawer. That label carries the arm length and the torque rating, and those two numbers decide what fits.
The gotcha we see on nearly every Whitney visit: a kit bought for a lighter gate gets swapped onto a heavier one during a previous repair and the arm burns out early every time. If the gate leaf has been rehung, widened, or had a board added since the original install, the original motor spec may already be the wrong one. We measure the leaf, check the rating, then match.
On the OEM-versus-aftermarket question for Ghost Controls specifically: genuine parts carry a known rating and warranty, and a fair number of aftermarket arms claim compatibility but run a different gearset. We’ll tell you plainly which is which, quote both, and let you decide. Ironworks Gate Co. Whitney is an independent service provider and not affiliated with Ghost Controls. We also service LiftMaster, Mighty Mule, and DoorKing.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Ghost Controls Gate Motor Replacement Is Failing
The pattern is usually slow before it’s sudden. These are the symptoms we diagnose most often in Whitney:
- Stalling halfway through the cycle. The motor can’t push through the mid-point resistance. A worn gearset or a leaf that has drifted out of alignment is the cause, and it gets worse as the gate binds further.
- Constant fault codes on the control board. Flashing codes usually mean the arm traveled outside its stall limits. A few of those are the board misreading a tired motor.
- Motor strains and labors but doesn’t move the gate. The gearset or the arm is done. Ghost Controls arms in single-gate kits typically wear out well before a Whitney homeowner expects, often within 5 to 7 years on a gate that sees daily use.
- Reversal on any pressure. The operator signals it needs retorque or a new arm. A gust the operator can’t read will trip the safety reversal and stop the gate mid-open.
- Bad or intermittent battery with a solar setup. Solar-charged systems in the Nevada heat lose battery capacity fast. A week of 105-degree days flattens a weak battery and the operator won’t run the arm. This one is often fixed without a new motor.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed pricing in Whitney breaks down roughly like this:
| Scope | Typical Installed Range |
|---|---|
| Single-gate motor replacement, standard residential | $650 – $950 |
| Single-gate motor replacement, heavy-duty arm or more complex install | $950 – $1,100 |
| Battery or solar charge accessory replacement only | $150 – $300 |
What drives the range: the arm’s torque rating, whether both gate leaves need service, whether wiring or the control board needs work, and whether the existing bracket setup is salvageable. Parts and labor are itemized separately. Upfront pricing is quoted and settled before any work starts, so you know the number. Every repair carries the 90-Day Done Right Promise: if it isn’t right, we come back and make it right. Current offer: $50 off any repair over $250.
DIY or Call Us?
What you can safely check yourself: whether the control board is powered, whether the battery is holding charge, whether the gate leaf swings free with the arm disconnected, and whether the nameplate on the arm is legible. Those checks save us time and can sometimes rule out a bad board instead of a bad motor.
Where DIY goes wrong for this part: a gate arm carries stored tension, and a wrong-size replacement strain the gate’s hinge or the operator’s gearing. The bigger risk is the 110-volt power run to the operator and the gate’s safety reversal edges. Wiring that back wrong, or leaving the safety edges untested, can leave you with a gate that closes on a car or a person. We handle the electrical properly. If you want the swap done right the first time in Whitney, call (855) 928-1304 for a free estimate.
FAQs
In Whitney, expect 5 to 7 years on a daily-use residential gate, and less if the gate is heavy or the motor is undersized. Battery-driven solar setups can go sooner because heat drains capacity. If yours is past that range and stumbling, replacement is the cost-effective path.
Sometimes, yes. If the fault is a worn battery, a bad control board, or a gearset that’s still serviceable, we repair. If the arm is burned, stalling, or the wrong spec for the gate, replacement is the correct fix. We don’t sell a replacement when a repair does the job.
Most single-gate motor replacements in Whitney finish in a few hours on one visit. Complex installs, dual-gate systems, or jobs that need new wiring can take longer, and we schedule those properly rather than rushing.
We source the correct Ghost Controls arm by model, rating, and capacity, then confirm fit before install. You get a written upfront price on parts and labor. Call (855) 928-1304 for a free estimate.
If your gate in Whitney is stalling, reversing, or throwing codes, the motor is usually the answer. We install Ghost Controls-compatible replacements properly, quote the price before any work starts, and stand behind every job with the 90-Day Done Right Promise. Call Ironworks Gate Co. Whitney at (855) 928-1304 for a free estimate today.
Written by the team at Ironworks Gate Co. Whitney, serving Whitney and nearby areas.