Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateLinear Gate Motor Replacement: The Whitney Owner’s Guide
We replace Linear gate motors in Whitney, and most swaps land between $650 and $1,200 installed, depending on the model, arm type, and whether the control board and safety edges need attention too. When a Linear operator fails, we can often get a technician out the same day to diagnose it and confirm the exact replacement before any work begins. Homeowners usually find out the hard way: the gate stops mid-travel, the arm groans and reverses, or the remote works only when you’re standing right at the driveway. In Whitney, where summer heat bakes the operator housing for months and winter cold snaps work the grease hard, we see Linear units fail at the motor capacitor or control board more often than the arm itself.
Which Linear Models This Applies To
Linear makes several swing and slide operators, and the replacement part depends on which one you have. The most common residential models we see on Whitney driveways are the Linear SW series swing operators, the older OSCO-line swing arms, and the slide operators in the LSO and similar lines. The model plate is usually inside the housing cover or on the back of the control box, and it tells you the exact series. Measure the arm stroke and gate weight before ordering anything: a replacement sized for a lighter gate will fail early, and an oversized operator strains the hinges. For Linear specifically, OEM parts are the safe call when the control board or receiver is the failed component, because aftermarket boards sometimes don’t talk to the original remotes. Quality aftermarket arms and motors are fine for mechanical wear items, and they cost less. We’re an independent service company and not affiliated with Linear, so we’ll tell you plainly which route makes sense for your unit.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Linear Gate Motor Replacement Is Failing
- The gate reverses for no reason. Usually a failing safety edge or a control board that’s misreading the obstruction signal. It’s a safety circuit problem, not just an annoyance, and it needs a proper diagnosis.
- The arm moves slowly or stalls in heat. A worn motor or a weak capacitor loses torque when the housing gets hot. In Whitney summers, we see this on units that ran fine all winter.
- The motor hums but the gate doesn’t move. Often a stripped gear or a failed capacitor. Humming without motion means the motor is trying but the drive train has given out.
- The remote works only up close. A failing receiver or a dying battery in the operator. Weak range is one of the earliest warning signs before a full failure.
- The gate drifts open or won’t stay closed. A limit switch or control board fault. Left alone, this can leave the gate unsecured, so it’s worth a same-day look.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed Linear gate motor replacement in Whitney runs about $650 to $1,200. The low end covers a straightforward swing-arm swap on an accessible gate with a working control board. The high end covers a slide operator, a new control board and receiver, or a gate that needs hinge or weld attention before the new motor goes on. The price we quote covers the operator, the labor, the wiring check, and a full travel and safety test before we leave. We settle the price upfront, before a single bolt is turned, so the bill matches the quote. Every replacement is backed by our written 90-Day Done Right Promise: if it isn’t right, we come back and make it right. Right now, $50 off any repair over $250 applies, and we offer a free second opinion on any written estimate you’ve already received.
DIY or Call Us?
You can safely check a few things yourself: the model plate inside the cover, whether the manual release works, and whether the gate swings freely by hand with the operator disengaged. If the gate binds by hand, the problem may be the hinges, not the motor. But this is where DIY goes wrong. Gate operators run on live 120-volt power, and the arm and spring assembly stores force that can injure you if it releases under load. Swapping a motor without matching the arm stroke to the gate weight, or without re-testing the safety edges, leaves a gate that fails again or fails dangerously. We’d rather you call. Our technicians have up to 13 years of experience, and we handle the power, the wiring, and the safety testing in one visit. Call (855) 928-1304 and we’ll get a technician out to your Whitney gate.
FAQs
A well-matched Linear operator typically lasts 10 to 15 years, though Whitney’s heat can shorten that on units with poor ventilation or heavy daily use. When yours starts reversing, stalling, or losing remote range, it’s worth a diagnosis before it fails completely.
Often, yes. A failed capacitor, control board, or safety edge can be replaced without a whole new motor, which saves money. We diagnose first and tell you honestly whether a repair gets you years more service or whether replacement is the better call. Call (855) 928-1304 for a free estimate.
Most Linear motor replacements are completed in a single visit, typically two to four hours once the correct part is on hand. If your model needs a special-order board, we’ll tell you upfront and schedule it, with the written price settled before we start.
We match the part to your exact Linear model from the housing plate and measurements, then source OEM or quality aftermarket based on what failed. We don’t claim to carry parts on a truck, so we confirm the part before the visit and keep the price fixed. Call (855) 928-1304 with your model number and we’ll take it from there.
We also service LiftMaster, Mighty Mule, Ghost Controls, and five other major gate-automation brands, so whichever operator is on your Whitney driveway, we can handle it. If your Linear motor is failing, don’t wait for it to quit mid-gate. Call Ironworks Gate Co. Whitney at (855) 928-1304 for a free estimate and a square deal: upfront pricing, no surprises, and work backed in writing.
Written by the team at Ironworks Gate Co. Whitney, serving Whitney and nearby areas.