Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateLinear Gate Parts & Welding in Whitney: What to Know First
We provide independent Linear gate parts and welding in Whitney, and most repairs are finished on the first visit. A worn hinge or a snapped weld on a Linear swing or slide gate typically runs $190 to $425 depending on the part and the access, and you’ll get the price in writing before we touch the gate. We’re not the cheapest bid in town and we don’t pretend to be. We’re the call that means the gate gets fixed once, closes square, and stays closed. If your Linear operator is straining, grinding, or the gate is dragging on its hinges, call us and we’ll tell you straight what it needs. A live person answers (855) 928-1304, day or night.
This page is for the Whitney homeowner whose Linear gate has started to fight back. Maybe the operator still runs but the gate sags. Maybe the weld at the post has cracked after a hard summer. You’ve had the gate a long time, you know its sounds, and something’s off. We know Linear hardware the way a mechanic knows an old truck: where it wears, what it tolerates, and what it won’t. Call (855) 928-1304 for a free estimate.
How Linear Products Fail – and How We Fix Them
Linear’s residential and light-commercial swing and slide operators are built to a budget and they hold up well when the gate beneath them is sound. Where they fail is almost always at the metal, not the board. Here are the failure modes we see most often on Linear jobs around Whitney, and what we actually do about each one.
- Post hinge fatigue on Linear swing operators. On swing gates running a Linear operator, the gate-side hinge post takes the full load of every open and close, and over years of Whitney’s summer heat the weld at the hinge plate works loose and starts to crack. You’ll hear it before you see it, a faint pop as the gate comes off full-open. We cut out the fatigued plate, weld a fresh hinge plate to the post, and re-hang so the operator isn’t fighting a sagging leaf. If we just replaced the hinge and left the cracked base, it would be back inside a season.
- Rail and track wear on Linear slide gates. Linear slide operators push the gate along its track, and when the rail dips or a roller seizes, the operator drags the whole gate and the motor strains. A common tell is the gate slowing near the end of travel, which most owners blame on the operator when the real cause is a worn roller or a rail that’s dropped at a joint. We true the rail, replace the rollers, and confirm the gate rolls with a push before we ever look at the motor.
- Cracked welds at the frame corners. Gate frames flex slightly every cycle. On older Linear gates, the corner welds are the first to crack, often on the hinge side where the load is highest. We grind the old weld back to sound metal, re-weld the joint properly, and dress it so the repair looks like it belongs. A weld over rust or paint is a short-lived fix, and we don’t do those.
- Latch and lock misalignment. When a gate sags even a quarter inch, the latch stops catching and the lock stops lining up, and owners start forcing it. On a Linear gate that’s almost always a hinge or post issue showing up at the latch. We fix the alignment at the source rather than shimming the latch, so the gate closes and the lock engages the way it should.
- Aftermarket part mismatches. Linear hardware isn’t universal, and we’ve seen gates where a previous repair used an aftermarket hinge or roller that fit the bolt holes but not the load. The part looks right and fails in a year. When we fit aftermarket parts on a Linear gate, we match them to the actual gate weight and cycle, and we tell you up front where the trade-off sits so you can decide.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Linear Gate Parts & Welding Process
Every Linear job follows the same steps, whether it’s a single hinge or a full re-weld. Here’s how it runs from your call to the cleanup.
- 1
The call. A live person picks up, day or night. We ask what the gate’s doing and how long it’s been doing it, and we book a visit that works around you.
- 2
On-site diagnosis. We check the metal first, the operator second. That means hinges, posts, rail, rollers, and welds before we open anything on the motor. On a Linear gate the two are connected, and a sound diagnosis saves you paying for parts you don’t need.
- 3
The parts decision. We lay out what’s worn, what an OEM Linear part costs against a quality aftermarket one, and where each makes sense. You get a written price before any work starts, no surprises on the bill.
- 4
The repair. We weld, re-hang, true the rail, or replace the latch, working to the gate, not just to the part. Most Linear jobs are done in a single visit.
- 5
The test. We cycle the gate through full open and close more than once, check the alignment at the latch, and watch the operator for strain before we call it done.
- 6
The guarantee and the cleanup. We leave the site the way we found it and back the work with our written 90-Day Done Right Promise. If it isn’t right, we come back and make it right.
See the difference
Before
After
Before
After
Before
AfterWhat Linear Gate Parts & Welding Costs in Whitney
Here’s a straight range for the most common Linear jobs in Whitney, so you know roughly where you’ll land before you call. These are the figures we work to, and your written estimate is settled before a single bolt is turned.
| Job | Typical Range |
|---|---|
| Hinge replacement | $190 – $320 |
| Gate rollers (set) | $160 – $280 |
| Latch & lock alignment / replacement | $150 – $275 |
| Rail repair or true | $240 – $480 |
| Custom welding (cracked frame, post, hinge plate) | $280 – $620 |
| Post replacement | $450 – $1,100 |
What moves the price: how much rust is under the failed part, whether the gate needs to come off to reach the weld, the gate’s weight, and whether the post is set in concrete or a surface plate. Linear hardware adds little to the bill on its own. The metal and the access do. Call (855) 928-1304 for a free estimate, and ask about the $50 Off Any Repair Over $250 and the permanent 5% Senior and Veteran discount.
Why Whitney Homeowners Call Ironworks Gate Co. Whitney for Linear Work
We’ve been a dedicated gate specialist since 1984, over 42 years, and we’re not going anywhere. Our technicians have up to 13 years of experience and they know Linear hardware the way they know the other brands on the driveway. That’s the reason to call us over a generalist: on a Linear job the fix is usually in the metal, and a handyman with a welder and no gate experience can weld a post true and leave the operator fighting a sagging leaf. We test the whole gate, operator included, before we leave.
Every Linear job is covered by our written 90-Day Done Right Promise, the Keystone Standard: if it isn’t right, we come back and make it right, no arguing. We also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so if your Linear shares a driveway with another brand, one call covers both. As an independent Linear service provider, we’re not affiliated with or authorized by Linear, and we say so plainly. What we are is the company that makes a Linear gate close like the day it was hung. Call (855) 928-1304, and a live person will answer, day or night.
FAQs
Can you get parts for my Linear gate the same day? Often, yes. Linear hinge, roller, latch, and frame hardware is common enough that we usually have what’s needed for a single-visit repair on a standard Linear swing or slide gate. If a particular part has to be ordered, we tell you the lead time and the price before we commit, and we schedule the return visit around it.
Does the repair affect my Linear operator warranty? A well-done weld or a correct hinge and roller replacement protects the operator rather than voiding it, because a gate that rolls and closes true puts less strain on the motor. We do the metal work properly, match parts to the gate’s actual load, and keep our repairs to the gate hardware and frame. If your Linear operator has its own manufacturer coverage, we work alongside it, and our 90-Day Done Right Promise backs the repair we do.
Should I repair my Linear gate or replace it? Repair first, in most cases. A cracked weld, a fatigued hinge plate, a worn roller set, or a sagging post are all fixable, and a well-built gate frame has decades of life left in it. We only recommend replacement when the frame itself has rusted through or the post is beyond welding. We check the metal before we talk about replacing anything, so you’re not sold a new gate you don’t need.
How fast can you get to a Linear gate repair in Whitney? Most Linear repairs are completed in a single visit, and we work around your schedule to get there. If your gate won’t close or won’t open, call (855) 928-1304 and a live person will answer, day or night, to get you booked. Estimates are free, and the price is agreed before any work starts.
What does a full Linear gate parts & welding job include? Diagnosis of the metal and the operator, the written price, the repair (welding, hinges, posts, rail, rollers, latch, or lock), a full open-and-close test, site cleanup, and our written 90-Day Done Right Promise. Call (855) 928-1304 for a free estimate on your Linear gate.
Written by the team at Ironworks Gate Co. Whitney, serving Whitney and nearby areas.