A Ironworks company - serving Whitney, NV

Linear Gate Motor & Opener in Whitney, NV

Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

Linear Gate Motor & Opener in Whitney: What to Know First

We provide independent Linear gate motor and opener service in Whitney, and most Linear repairs are finished in a single visit. A dead Linear slide or swing operator usually comes down to the control board, the limit switch, or the battery backup, and we diagnose all three before quoting a price. You’ll get an upfront number settled before a single bolt is turned, backed by our written 90-Day Done Right Promise. This page is for Whitney homeowners who already have a Linear unit on the driveway and want it working correctly, not replaced on a hunch. Call (855) 928-1304 and a live person picks up, day or night.

Call (855) 928-1304

How Linear Products Fail – and How We Fix Them

Linear builds solid residential operators, and the Linear-branded units we see around Whitney tend to fail in predictable ways. Knowing the pattern saves you from paying for parts you don’t need.

  • Control board failure on the Linear LSO/LS-series slide operators. The board is where most Linear slide motor problems start. A unit that runs a few inches and stops, or clicks but won’t move, is often a board that’s lost its programming after a power surge. We test the board under load and, when it’s the culprit, replace it with a Linear OEM board so the limit programming and remote codes carry over cleanly.
  • Limit-switch drift on swing operators. Linear swing openers use mechanical limit switches, and after years of heat cycling the arm travel creeps until the gate over-travels or reverses halfway. The symptom is a gate that won’t fully close or bounces back. We reset the limits and check the arm geometry rather than just nudging the switch, because drift usually means a worn hinge or a sagging post is pushing the gate out of alignment.
  • Battery backup that won’t hold. Linear battery-backup units in Whitney take a beating from summer heat, and a sealed battery that’s three or four years old will fail the moment the power drops. If your gate won’t open during an outage, the battery is the first thing we check, and we replace it with a correctly rated cell, not a generic one that fits the tray but not the charge profile.
  • Gear and drive-train wear. On older Linear slide motors the drive gear and the chain or belt wear together, and the unit starts to sound labored or slip under load. We inspect the gearbox and the drive train together, since replacing one without the other just moves the failure down the line.
  • Intercom and keypad wiring at the operator. When a Linear operator is paired with an intercom or a keypad, a loose low-voltage connection at the control board is a common reason the gate “won’t respond” even though the motor is fine. We trace the accessory wiring at the board before assuming the operator has failed.
Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Our Linear Gate Motor & Opener Process

Every Linear job follows the same path, from the first call to the final walk-through.

  1. 1
    Diagnose on site. We test the motor, control board, limits, battery backup, and any intercom or keypad wiring, then tell you plainly what’s wrong.
  2. 2
    Decide OEM versus aftermarket. We explain the trade-off and let you choose: a Linear OEM part for a warranty-safe, exact fit, or a quality aftermarket equivalent when it makes sense for the age of the unit. No surprises on the bill either way.
  3. 3
    Repair. We make the fix with the gate secured and the power isolated, following the manufacturer’s procedure so nothing downstream is disturbed.
  4. 4
    Test under real load. We cycle the gate open and closed multiple times, check the safety edges and reversal, and confirm the battery backup engages when power is cut.
  5. 5
    Clean up and guarantee it. We leave the site as we found it and back the work with the written 90-Day Done Right Promise.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

What Linear Gate Motor & Opener Costs in Whitney

Linear gate motor and opener work in Whitney falls into a few realistic ranges. These are typical figures, and your exact price depends on the model and what we find on site.

Scenario Typical Range
Diagnostic visit and limit/battery reset $95 – $150
Battery backup replacement (Linear OEM cell) $180 – $320
Control board replacement (Linear LSO/LS series) $350 – $650
Gear / drive-train repair on slide motor $300 – $600
New Linear slide or swing motor installation $1,200 – $2,400

What moves the price: the model series, whether the part is OEM or aftermarket, gate weight and travel on a slide unit, and whether accessory wiring needs redoing. We quote and agree the price before any work starts. Estimates are free, and ask about $50 Off Any Repair Over $250.

Why Whitney Homeowners Call Ironworks Gate Co. Whitney for Linear Work

We’re an independent Linear service provider, and we know these units from the inside out. Our technicians have up to 13 years of experience, and they’re trained and equipped across nine gate-automation brands, so if the fix turns out to be a different system than expected, we’re still the right call. A live person answers the phone 24 hours a day, every day, not a voicemail. Every job is covered by our written 90-Day Done Right Promise: if it isn’t right, we come back and make it right. Senior and Veteran 5% discount is standing. If you’ve weighed us against someone who handles only one brand, we also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing in Whitney. Call (855) 928-1304.

FAQs

Need Gate Repair help nationwide? Licensed & insured · 1-hour response · free estimates
Call (855) 928-1304
Local Service Coverage

Request a Free Estimate in Whitney

Tell us what you need - Ironworks Gate Co. Whitney responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch