Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFAAC Welding & Fabrication: The Whitney Owner’s Guide
We repair and fabricate FAAC gate welding and fabrication components in Whitney, and most welding repair jobs run $275 to $650 depending on whether we’re re-welding an existing FAAC hinge point or fabricating a replacement bracket from scratch. We can often get to a failing weld the same day you call, especially when a gate leaf has started to sag or drag against the ground. Welding on a FAAC gate isn’t a cosmetic patch – a broken hinge weld, a cracked mounting plate, or a fatigued operator bracket on a FAAC 400-series or 740-series swing operator usually shows up as a gate that binds, groans, or stops halfway through its arc. Owners in Whitney tend to notice it in summer, when the desert heat pushes steel and welds that were already stressed.
Which FAAC Models This Applies To
Welding and fabrication work applies across the FAAC swing and barrier lines, but the parts differ enough that model identification matters before anyone strikes an arc. The most common FAAC residential units we see in Whitney are the 400-series and 740-series swing operators, along with older 390-series drives on gates that have been in the ground twenty years or more. The fabrication side, though, is usually about the gate itself: hinge plates, post brackets, operator mounting arms, and the steel tabs the FAAC arm bolts to. Check the label inside the operator housing or on the control board for the model number, and measure your post spacing and gate-leaf thickness before you order anything. On FAAC equipment, an OEM bracket is the safer call when the gate carries the original arm geometry, because a slightly off aftermarket tab changes the arm’s swing arc and loads the operator motor harder. We’re an independent service provider and not affiliated with FAAC, so we’ll tell you plainly when an OEM part is worth the wait and when a fabricated equivalent will outlast it.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your FAAC Welding & Fabrication Is Failing
Most owners in Whitney discover a weld problem before they discover the weld. Here’s what to watch for:
- The gate sags or drags on one side. A cracked hinge weld or a fatigued post bracket lets the leaf drop a fraction of an inch, and the FAAC arm then fights the misalignment on every cycle.
- The operator strains or times out mid-swing. When the mounting bracket has shifted, the arm geometry is off and the FAAC motor draws more current than it should. The control board trips on obstruction even when nothing is in the path.
- Visible rust bleeding from a joint or bracket. In Whitney’s dry climate, rust streaks at a weld seam usually mean the weld itself has cracked and is holding moisture. Surface rust on flat steel is normal; rust tracing a line is not.
- A popping or clunking sound as the gate moves. That’s slack in a failed weld or a worn hinge plate, and it only gets worse once the operator starts loading a compromised joint.
- The gate leaf wobbles when you push it by hand. Grab the gate with the operator off and rock it. Any movement at the hinge or post bracket means the weld or the fabrication has given way and needs attention before the FAAC arm damages itself.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Welding and fabrication pricing in Whitney runs a real range because the work ranges too. A straightforward re-weld on an accessible hinge runs $275 to $400. Fabricating a replacement bracket or mounting plate, priming and painting it, and re-hanging the leaf runs $400 to $650. If the post itself has to be reset or a new steel section added, that pushes higher. Call (855) 928-1304 for an exact quote – estimates are free.
What drives the range: how much steel has to be cut out and replaced, whether the gate has to come off the hinges to reach the weld, and how much finish work the repair needs to look right. We quote the price upfront and put it in writing before a single bolt is turned, so there’s no surprise on the bill. Every job is backed by our 90-Day Done Right Promise.
| Scope of work | Installed range |
|---|---|
| Re-weld existing hinge or bracket (gate stays hung) | $275 – $400 |
| Fabricate replacement bracket or plate, prime & paint | $400 – $650 |
| Post reset or added steel section | Quoted on site |
DIY or Call Us?
Some things you can check safely yourself. Look for rust lines at the welds, push the gate by hand to feel for wobble, and read the model label inside the FAAC operator. That tells us a lot before we arrive. What you shouldn’t do is weld a loaded gate or a hinge under tension yourself. A gate leaf can weigh several hundred pounds, and cutting or welding on a joint that’s carrying that load can drop it without warning – onto a hand, a foot, or a car in the driveway. The same goes for the operator arm, which can move when power is restored. This is genuinely dangerous work, so we’d rather you call (855) 928-1304 and let a trained tech assess it. Estimates are free and there’s no pressure.
FAQs
Roughly 15 to 25 years on a well-built gate in good soil, though Whitney’s swing between dry heat and occasional monsoon moisture stresses welds faster than a mild climate does. A weld done properly with good prep and finish lasts far longer than a quick deck-welding job.
Often yes. A cracked weld can usually be ground out and re-welded rather than replaced whole, which saves money and keeps your original FAAC mounting geometry intact. We’ll tell you honestly which option is the better value once we’ve seen it.
Most re-welds are finished in a single visit of an hour or two. Fabricating a custom bracket takes longer because it’s measured, cut, and finished before it goes on, so we’ll give you a realistic window when we quote.
We match the part to your FAAC model and to the gate’s actual measurements, then choose between OEM and a fabricated equivalent based on what your arm geometry needs. We don’t stock parts or carry them on a truck – the right part is ordered or made for your gate.
Whether you have a FAAC gate or one running LiftMaster, Mighty Mule, or Ghost Controls automation, the welding and fabrication approach is the same: measure, match, and fix it right the first time. Give us a call at (855) 928-1304 for a free estimate, and we’ll get your Whitney gate closing like it should.
Written by the team at Ironworks Gate Co. Whitney, serving Whitney and nearby areas.