Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFAAC Keypad & Intercom Repair: The Whitney Owner’s Guide
Replacing a failed FAAC keypad or intercom in Whitney typically runs $285 to $520 installed, depending on whether you have a standalone keypad, a combined keypad/intercom unit, or a multi-unit entry station, and most of that work is done in a single visit. We’re an independent service provider, not affiliated with FAAC, but keypads and intercoms on FAAC systems are core work for us and we stock the common replacement parts for scheduled jobs. Owners usually find out the hard way: the code that worked for years suddenly needs three tries, the call button rings inside but no one can hear the visitor, or the keypad beeps and the gate just sits there. Whitney’s summer heat and winter cold swings are hard on outdoor keypads, and most failures show up in the same handful of ways.
Which FAAC Models This Applies To
FAAC keypads and intercoms show up across the 400, 390, 391, 844, and S418 operator families, and the entry station you have may not match the operator model stamped on the control board. That’s the first compatibility gotcha we see in Whitney: a homeowner replaces the keypad but the new unit won’t talk to the older FAAC control board because the interface type is different (Wiegand versus a proprietary bus). Before we quote anything, we read the label on the back of the keypad or intercom housing, measure the housing cutout, and check the wire count at the operator. FAAC has run several versions of the same-named keypad over the years, and the mounting pattern and connector pinout changed between them. OEM replacement is the safe call when your unit is more than about eight years old and you want the same fit and behavior. A quality aftermarket equivalent can cost 30% to 40% less and works fine on newer operators, but the wiring has to be re-terminated and the access codes re-entered by hand. We’ll tell you which one makes sense for your specific FAAC in Whitney rather than defaulting to the pricier option.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your FAAC Keypad & Intercom Repair Is Failing
Most Whitney owners call us after one of these five symptoms shows up. Each one points to a specific part inside the unit, and knowing which helps us quote honestly.
- Codes only work on the second or third try. The keypad membrane or the tactile switches underneath have worn through. The keypad isn’t dead, it’s just not registering every press, and this gets worse fast in Whitney’s dry heat.
- The keypad beeps but the gate doesn’t move. The keypad is sending a signal but the operator’s control board isn’t accepting it, usually because the wiring connection at the board has corroded or loosened. This is a repair, not a replacement, in most cases.
- Visitor presses the call button and hears nothing back. The intercom speaker or microphone has failed, or the audio wire run has a break somewhere between the pedestal and the house. We test both ends before quoting.
- The keypad backlight is out and the buttons feel stiff. Moisture has gotten inside the housing and the internal board is oxidizing. Whitney’s occasional hard freezes after rain are the usual trigger, and this is the one symptom that almost always means a full replacement.
- Codes stop working entirely after a power blink. The keypad’s memory has lost its programming, which points to a failing backup battery or a bad control board inside the unit. We can often re-program it, but if it forgets again within a few months, the board is done.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed prices in Whitney for the work we do most often, parts and labor together:
| Job | Installed range |
|---|---|
| Standalone FAAC keypad, replace and re-program | $285 – $395 |
| Combined keypad/intercom unit, replace and re-program | $380 – $520 |
| Wiring repair or re-termination at the operator (keypad reused) | $150 – $260 |
| Multi-unit entry station (apartment or shared drive) | $550 – $900 |
The range depends on the unit, whether the wire run needs repair, and whether the control board has to be re-configured. We quote the price before any work starts, and you approve it in writing. The gate itself and the operator stay untouched unless we find a separate problem. Every keypad and intercom job carries our 90-Day Done Right Promise: if it isn’t right, we come back and make it right.
DIY or Call Us?
Some things you can safely check yourself. Confirm the keypad is getting power (most have a small LED), look for obvious moisture or insect intrusion in the housing, and try re-entering a code you know is correct to rule out a simple programming issue. What you shouldn’t do is open the operator cabinet and poke around the control board or the low-voltage wiring while the gate is powered. FAAC operators run on line voltage inside that cabinet, and the capacitors hold a charge after the breaker is off. That’s genuinely dangerous, and it’s not a place for a homeowner with a screwdriver. Beyond the cabinet, soldering wire connections in a wet Whitney winter is where DIY jobs tend to fail a few months later. If the keypad is working but the gate isn’t, or you’re not comfortable inside the housing, call us at (855) 928-1304 and we’ll sort it out.
FAQs
How long does a FAAC keypad or intercom last in Whitney? Most outdoor FAAC keypads last 8 to 12 years here, with the low end common on units exposed to full afternoon sun and the high end on covered or shaded entries. Whitney’s heat and occasional hard freezes are the two biggest factors.
Can it be repaired instead of replaced? Yes, often. Wiring faults, programming loss, and loose control-board connections are repair jobs that cost $150 to $260 installed. Membranes, speakers, and oxidized boards are usually not worth repairing once the unit is more than a decade old.
How long does the swap take? A standalone keypad is a 60 to 90 minute job. A combined keypad/intercom or a multi-unit entry station runs two to three hours, mostly because of re-programming the access codes and testing the call and audio path.
How do you source the part? We match your FAAC model and housing to the correct OEM replacement or a quality aftermarket equivalent, order it, and schedule the install. We don’t claim to carry parts on a truck; we come prepared for your specific job. Scheduling is usually within a few business days of approval, and we’ll give you a firm date when we quote the work.
We also service keypads and intercoms on LiftMaster, Mighty Mule, and Ghost Controls gates, so if your system is a mix or you’re not sure what you have, we’ll figure it out. Call (855) 928-1304 for a free estimate on your FAAC keypad or intercom repair in Whitney. Live person, 24 hours a day.
Written by the team at Ironworks Gate Co. Whitney, serving Whitney and nearby areas.