Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFAAC Access Control Installation: The Whitney Owner’s Guide
FAAC access control installation in Whitney typically runs $650 to $1,900 installed, depending on whether you’re replacing a keypad and receiver or adding a full entry system with intercom and vehicle detection. Most of these jobs are scheduled rather than same-day, because the right unit has to be matched to your FAAC operator and ordered for your gate. If your keypad beeps but the gate won’t move, or the entry pedestal has gone dead after a summer of triple-digit heat, you’re in the right place.
Owners rarely discover an access control failure all at once. It usually starts with a code that takes two or three tries, then a remote that only works when you’re ten feet from the gate, then a keypad that lights up but sends nothing. By the time someone calls us, the gate has usually been propped open for a week. We see it constantly in Whitney, where afternoon sun hits a west-facing keypad pedestal for six hours straight.
Which FAAC Models This Applies To
FAAC builds swing and sliding operators across several lines, and the access control side you need depends on which one is on your driveway. The common residential units in Whitney are the 390, 391, 400, 402, 740, 844, and the S800H and C720 sliding operators. Each takes a different receiver, and the older 390/391 boards in particular use a receiver plug that newer 844 controllers won’t accept without an adapter. That’s the compatibility gotcha that catches most homeowners who order online: the keypad looks right, the receiver won’t plug in.
Before you buy anything, find the label on the operator housing (usually inside the cover, sometimes on the underside of the arm) and write down the exact model and the board revision letter. If the label is sun-bleached and unreadable, a photo of the control board itself tells us what we need. FAAC’s OEM receivers and entry panels are well made and we use them when the budget allows. For a failing keypad on a 15-year-old operator, a quality aftermarket 433 MHz or 868 MHz receiver paired with a weather-rated pedestal often outlasts the original and costs less, as long as the frequency and coding match your existing remotes. We’re an independent service provider, not affiliated with FAAC, so we recommend whatever actually fits your gate rather than whatever’s on a shelf.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your FAAC Access Control Installation Is Failing
- Keypad lights up but the gate doesn’t respond. The keypad’s power supply is fine; the relay or the receiver behind it has failed, or the code memory has corrupted after a voltage dip. Common after monsoon-season lightning in the valley.
- Remotes work only up close. The receiver antenna has corroded at the connector, or the receiver board itself is losing sensitivity. Desert dust builds a conductive film on the board that shorts the traces over time.
- Intermittent operation in afternoon heat. A control board or power supply that’s marginal at 70 degrees can drop out at 110. This is a heat-related component failure, not a gate problem, and it gets worse every summer.
- Entry pedestal or call box dead. Usually the low-voltage power run has failed at a buried splice or the transformer has given out. Water intrusion at the pedestal base is the culprit nine times out of ten.
- Gate opens on its own. A stuck relay, a failed loop detector, or a receiver picking up a neighbor’s signal on a shared frequency. This one needs attention quickly because it’s a security issue, not just an annoyance.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Whitney, a keypad-and-receiver replacement runs $650 to $950 installed. A full entry pedestal with intercom and vehicle loop detection runs $1,200 to $1,900. Adding access control to a FAAC operator that never had it typically lands between $800 and $1,400 depending on the power run. The range is driven by three things: which FAAC model you have, how far the pedestal sits from the operator, and whether the low-voltage run needs to be replaced or just reterminated.
Every price we quote includes the part, the labor, and cleanup, and it’s agreed before a single wire is pulled. No surprise line items for the transformer or the splice kit. The work is backed by our 90-Day Done Right Promise, written and no-hassle. If the keypad fails in week six, we come back and make it right.
| Job | Installed range |
|---|---|
| Keypad + receiver replacement | $650 – $950 |
| Entry pedestal with intercom and loop | $1,200 – $1,900 |
| Add access control to existing FAAC operator | $800 – $1,400 |
DIY or Call Us?
Some things you can check safely yourself. Confirm the keypad has power (most have a small LED), look for obvious corrosion on the receiver antenna, and make sure the operator’s own manual control still opens the gate. That last check tells you whether the problem is the gate or the entry system. If the gate opens fine from the operator but not from the keypad, the problem is in the access control, not the operator.
Where DIY goes wrong: access control wiring lives at 12 to 24 volts, which won’t kill you, but a wrong connection can fry a $400 control board in a second. And any work on the 120-volt feed to the transformer is genuinely dangerous; that belongs to a licensed electrician, not a weekend project. With up to 13 years of technician experience across our team and training on nine gate-automation brands, we get the diagnosis right the first time. Call (855) 928-1304 for a free estimate, and we’ll match the part to your FAAC model before anything gets ordered.
FAQs
Expect 8 to 12 years for a quality keypad in Whitney’s climate, and less for a unit in full afternoon sun. UV exposure and dust are the two things that shorten life here more than anywhere back east; a pedestal in shade routinely outlasts one in direct west-facing sun by three or four years.
Sometimes, yes. A failed relay or a corroded antenna connector can often be repaired for $150 to $300, and we’ll tell you honestly when that’s the better call. Once a board has heat damage or the keypad membrane has cracked, replacement is usually the cheaper path over the next five years.
A straight keypad and receiver swap takes about two hours. A full pedestal replacement with a new power run runs half a day, and we schedule it so your gate isn’t left open overnight. Call (855) 928-1304 and we’ll give you a firm time window.
We order the specific receiver or entry panel that matches your operator’s model and board revision, from FAAC’s distribution or a verified aftermarket supplier whose frequency and coding match your existing remotes. We confirm the part number with you before ordering so there’s no wrong-part return. Call (855) 928-1304 for an exact quote; estimates are free.
If your FAAC access control has you parking and walking to the gate, it’s time to fix it properly. Ironworks Gate Co. Whitney handles the full scope, from the keypad and receiver to the wiring and the operator, and we do it right the first time with a written guarantee behind it. We also service LiftMaster, Mighty Mule, and Ghost Controls systems, along with the other major brands on our bench. Call (855) 928-1304 today for a free estimate, and we’ll match the right part to your gate and give you a square price before any work starts.
Written by the team at Ironworks Gate Co. Whitney, serving Whitney and nearby areas.