Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFAAC Gate Motor & Opener in Whitney: What to Know First
We provide independent FAAC gate motor and opener service in Whitney, and most FAAC repairs are finished on the first visit. If a board or specific motor has to be ordered, the wait is usually a few days rather than weeks. You get an upfront price agreed before any work starts, so nothing on the bill comes as a surprise.
This page is for Whitney homeowners who own a FAAC gate and want it fixed correctly by someone who knows the brand, not by a generalist guessing at it. As an independent FAAC service provider, we aren’t affiliated with or authorized by FAAC. We work on the equipment the way a good mechanic works on a car: to the maker’s spec, with the right parts. Call (855) 928-1304 and a live person answers, day or night.
How FAAC Products Fail – and How We Fix Them
FAAC builds solid automation, and the failures we see in Whitney tend to be predictable once you know the model and the conditions here. These are the ones we run into most:
- FAAC 391 and 390 slide operators – worn limit switches. On the 391, the gate starts stopping a few inches short or running past the open point. Owners often assume the control board is gone. Usually it’s the limit switch or its cam, worn from years of travel. We reset or replace the switch and re-teach the travel limits rather than selling a board the gate doesn’t need.
- FAAC 400-series swing operators – battery and charging faults. The 402 and 422 run on a backup battery that keeps the gate working through a power dip. After several summers here the battery weakens and the gate slows, then stalls mid-swing. We test the battery under load and check the charger output, because a weak charger will kill a new battery too.
- FAAC 740 and 741 slide operators – worn pinion and chain drive. Grinding or a jump at the start of travel points to a worn pinion gear or stretched chain, not always the motor. We inspect the drive train before touching the motor, and replace the gear set when that’s the honest fix.
- FAAC S418 swing arms – arm and hinge wear. On lighter residential swing gates, the arm bushing wears and the gate sags or binds. That extra drag burns out the motor over time. We correct the hinge geometry and the arm before the motor pays for it.
- FAAC E-series control boards – moisture and surge damage. Summer storms and irrigation overspray get into enclosures. A board that’s corroded or has taken a surge shows intermittent behavior that looks random. We check the board and the enclosure seal, and we’re honest when a board is genuinely gone versus when it’s a loose connection.
Whatever the model, we treat the whole gate – hinges, posts, and drive – because a FAAC motor that’s fighting a dragging gate will fail again no matter how many times it’s repaired.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our FAAC Gate Motor & Opener Process
- 1
We answer the phone and ask the right questions. A live person takes your call any hour. We ask the model if you know it, what the gate is doing, and whether it’s stuck open or closed, so we arrive prepared.
- 2
We diagnose on site. We test the motor, the board, the limits, and the gate’s mechanical travel. The fault is usually obvious once the gate is moving under load.
- 3
We make the parts call honestly. Sometimes OEM is the right choice for a clean fit and warranty-safe repair. Sometimes a quality aftermarket part does the same job for less. We tell you which and why, and you decide.
- 4
We quote before we touch a bolt. The price is written and agreed before any work starts. No surprises when the job is done.
- 5
We repair and test. We run the gate through full open and close cycles, check the safety edges and the reverse function, and confirm the limits hold.
- 6
We clean up and back it in writing. Every FAAC job carries our 90-Day Done Right Promise. If it isn’t right, we come back and make it right.
See the difference
Before
After
Before
After
Before
AfterWhat FAAC Gate Motor & Opener Costs in Whitney
FAAC work in Whitney generally falls into a few ranges. These are honest ballparks for a residential gate; your exact price depends on the model and what we find.
| Job | Typical Range |
|---|---|
| Diagnostic and repair (limits, arm, connections) | $180 – $340 |
| Battery and charger service (400-series) | $220 – $400 |
| Control board replacement | $350 – $650 |
| Full FAAC motor replacement (slide or swing) | $900 – $1,800 |
| New FAAC operator installation, measured and scheduled | $1,400 – $2,600 |
What moves the price is the model, whether the drive train or gate itself needs mechanical work, and OEM versus aftermarket parts. A full installation isn’t a same-day job – it’s measured, ordered, and scheduled, with a free measure and a written price before anything is ordered. Call (855) 928-1304 for an exact quote; estimates are free and the price is agreed before work starts.
Why Whitney Homeowners Call Ironworks Gate Co. Whitney for FAAC Work
Whitney homeowners call us because the job gets done once, correctly, and backed in writing. Our technicians have up to 13 years of experience, and they’re trained on nine gate-automation brands – not just FAAC. If your FAAC needs a part we don’t stock, we might find the fix in a LiftMaster, Mighty Mule, Ghost Controls, or DoorKing cross-reference while we’re at it, so you’re not waiting on a single source. Every job carries the 90-Day Done Right Promise: a written guarantee with no arguing. A live person answers the phone 24 hours a day, and our background-checked, uniformed technicians work in your home the way they’d work in their own mother’s.
FAQs
Not when it’s done correctly with the right parts. We use OEM parts or quality aftermarket parts that meet spec, and we won’t do anything that compromises a covered component. If your FAAC is still under warranty, tell us when you call so we can protect it. Call (855) 928-1304 and we’ll talk it through.
For most FAAC repairs, yes – many are done on the first visit. If your model needs a specific board or motor ordered, the wait is usually a few days. A new installation is different: it’s measured and scheduled, not same-day. Call (855) 928-1304 for a free estimate and we’ll tell you straight.
Repair is usually the right call unless the motor is failing repeatedly or the model is discontinued with no parts. A 391 or 402 with a single fault is almost always worth fixing. We’ll give you both numbers honestly so you can choose. Call (855) 928-1304 for a free second opinion on any written estimate.
We can source FAAC parts for the common residential models, and when we can’t, we find a spec-matched alternative. You won’t be left ordering parts yourself. Call (855) 928-1304 and we’ll confirm what your model needs.
Repairs are often same-day or next-day, and a live person answers the phone any hour, so call whenever the gate fails. Installations are scheduled after a free measure. Call (855) 928-1304 – we’ll give you a real timeframe, not a line.
Written by the team at Ironworks Gate Co. Whitney, serving Whitney and nearby areas.