Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Installation Cost in Whitney?
Gate installation in Whitney typically costs $3,200 to $7,800 for a single residential driveway gate, and $6,500 to $14,000 for a full automated double gate with access control. The biggest swing factors are gate material (steel vs. wrought iron vs. aluminum), drive width, and whether the opener and keypad entry are part of the job. Most Whitney homeowners planning to stay put should budget around $5,000 to $9,000 for a gate that will last decades and close the same way in year twenty as it did on day one.
We install driveway and estate gates in Whitney every week, and the numbers below come from actual jobs in this valley, not a national average bought off a spreadsheet. If you want a firm number for your property, call (855) 928-1304 and we’ll come out and price it in writing, free.
Gate Installation Cost Breakdown (2026)
Here is what each piece of a gate job actually runs in the Whitney market this year. Prices include fabrication, and most include installation labor on a standard 12-to-16-foot driveway.
| Line Item | Typical Range (Whitney, 2026) |
|---|---|
| Basic steel single swing gate (12 ft, no automation) | $2,400 – $4,200 |
| Wrought iron double swing gate (14 – 16 ft opening) | $4,800 – $8,900 |
| Aluminum ornamental gate (lighter, rust-resistant) | $3,100 – $6,400 |
| Sliding gate (track or cantilever) | $5,200 – $11,500 |
| Swing gate opener (single arm, installed) | $1,400 – $2,600 |
| Sliding gate operator (installed) | $1,800 – $3,400 |
| Keypad or telephone entry access control | $650 – $1,900 |
| Safety loops, photo-eyes, and edge sensors | $400 – $900 |
| Concrete footings and post setting | $600 – $1,600 |
| Electrical trenching and low-voltage run (per foot) | $12 – $28/ft |
| Permit and inspection fees | $150 – $450 |
Add those up and a typical automated double gate in Whitney lands between $7,000 and $11,000, depending on how far the gate sits from the power source and how much concrete work the site needs. The gate itself is often less than half the bill. The automation, safety devices, and site prep are where the real money goes, and where a cut-rate installer will quietly leave things out.
What pushes the number up
A long driveway is the most common reason a Whitney quote comes in higher than the homeowner expected. Every additional foot of trenching for power and low-voltage control wire adds cost, and if the gate is 200 feet from the house, that adds up fast. Custom fabrication, steep grades, caliche-heavy soil that fights a shovel, and stone or stucco pillar work all add to the total. On the automation side, a sliding gate costs more than a swing gate because of the track or cantilever hardware, but it’s often the right call on a sloped driveway where a swing gate would drag or bind.
What Affects Gate Installation Pricing in Whitney
- Driveway width and grade. A standard 12-foot single gate is the least expensive option. Whitney homes with wide RV access, especially in the older neighborhoods off Whitney Ranch and along Sunset Road, often need a 16-to-20-foot opening, which raises both the gate and the operator cost.
- Material choice. Steel is the workhorse and the best value for a gate that has to hold up to desert sun and wind. Wrought iron costs more and looks it. Aluminum is lighter and won’t rust but dents more easily. We’ll walk you through the tradeoff honestly, because the wrong material for your driveway is a decision you’ll live with for twenty years.
- Soil and site work. Much of the Whitney area sits on hard caliche that has to be broken out before a footing goes in. That’s a real cost line, and any installer who hasn’t dug in this Valley before will underestimate it.
- Power source. If there’s an outlet or panel near the gate, great. If not, trenching a new run from the house is a meaningful part of the quote. Solar operators exist and we install them, but they’re not the answer for every gate.
- Automation brand and features. A basic arm opener is one number; a LiftMaster or FAAC operator with keypad, safety loops, and smartphone access is another. We’re certified on nine major brands, so we spec the right one for your gate rather than pushing whatever’s on the shelf.
- Permits. Whitney and Clark County require permits on most automated gate installations, and the fee is small compared to the cost of a gate that fails inspection or a job that has to be redone. We handle the paperwork.
One local note that surprises people: desert wind and blowing grit wear out cheap gate hardware quickly. Ball-bearing hinges and quality operators cost a little more up front and save you a repair call every couple of years. That’s part of why we push toward the right hardware the first time. Our full Gate Installation in Whitney service page goes deeper on materials and options.
How to Save on Gate Installation
You don’t have to spend the top of the range to get a gate you’ll be happy with. A few practical ways to keep the number down without cutting into the things that matter:
- Get a free written second opinion on any estimate. If a contractor has already quoted you, bring it to us. We’ll read it line by line and tell you where the numbers look thin and where they look fair. No charge, no pressure. It’s a standing offer.
- Match the gate to the driveway. If your drive is 12 feet wide, a 12-foot gate protects it. A 20-foot gate you don’t need is money in the ground.
- Put power and control wire in the ground once. If the trench is already open, add the access-control wiring now. Digging it up later costs more than the wire ever will.
- Ask about the $89 seasonal tune-up. A gate that’s dialed in runs smoother and lasts longer, and a tune-up is a lot cheaper than an emergency repair call.
- Seniors and veterans always get 5% off. No expiration, no fine print. It applies to the job.
Can you fix it cheaper than you can replace it?
Often, yes. If your existing gate has good bones and the problem is hinges, a bent frame, or an opener that’s finally given up, repair is usually the smarter money. We’ll give you an honest answer on whether to repair or replace, and we don’t push a new gate when the old one has years left. If a repair is the better call, that’s the quote you’ll get. Call (855) 928-1304 and we’ll tell you straight.
How the Installation Works, Step by Step
Knowing the sequence helps you plan and keeps surprises off the bill. Here’s how a Whitney gate job typically runs:
- Free on-site estimate. We measure the opening, check the grade, look at power, and talk through materials. You get an upfront written price before any work begins.
- Permit and layout. We pull the required permit and mark post locations, confirming the swing direction and clearances.
- Concrete footings. Posts are set in concrete sized to hold a years-long gate in this soil. This is the step that’s easiest to cut and does the most damage if you do.
- Fabrication and hang. The gate is built to the measured opening, then hung with quality hinges so it swings true from day one.
- Opener and control wiring. Electrical and low-voltage control lines are trenched and pulled, then the operator is installed and programmed.
- Safety devices and walk test. Photo-eyes, safety loops, and edge sensors are installed and tested. The gate is run through a full-cycle check to confirm it stops and reverses the way it should.
- Walkthrough and handed-off paperwork. We walk you through operation and leave the job clean, backed in writing by our 90-Day Done Right Promise.
FAQs – Gate Installation Cost
How much does a driveway gate cost installed in Whitney?
A single residential driveway gate in Whitney runs $2,400 to $4,200 without automation, and $3,800 to $6,800 once you add a single-arm opener. A double gate with full automation and access control is $7,000 to $14,000. Call (855) 928-1304 for a free, written estimate that reflects your driveway.
Is it cheaper to install a swing gate or a sliding gate?
A swing gate is almost always the cheaper install, usually $1,000 to $2,500 less than a sliding gate on the same opening. Sliding gates cost more because of the track or cantilever hardware. That said, if your driveway is sloped, a sliding gate can save money over time by avoiding the constant binding a swing gate suffers on an incline. Call us and we’ll look at your grade and give you a straight recommendation.
Do I need a permit for a gate in Whitney?
Yes, most automated gate installations in Whitney and Clark County require a permit, and the fee generally adds $150 to $450 to the job. We handle the permit and inspection as part of the estimate. Skipping the permit to save a few hundred dollars can cost far more if the gate later fails an inspection or has to be redone. Call (855) 928-1304 with questions.
How much does gate automation cost in Whitney?
Adding an opener to an existing gate runs $1,400 to $2,600 for a single swing operator and $1,800 to $3,400 for a sliding operator, installed. Keypad or telephone entry access control adds $650 to $1,900, and safety devices add $400 to $900. We’re certified on nine major opener brands, so you get the right fit for the gate you have. Call for an exact quote, free.
Can you come today?
For most Whitney gate installations, we schedule an on-site estimate first, often within a day or two, because we won’t quote a price we haven’t measured. Call (855) 928-1304 and a live person answers 24 hours a day. If your existing gate is broken and you need a repair rather than a new install, call today and we’ll tell you what’s possible on the schedule.
Why Ironworks Gate Co. Is the Right Call in Whitney
We’re a company that does a few things well: driveway and estate gates, and nothing else. Our technicians have up to 13 years of experience, they’re background-checked and uniformed, and they work in your home the way they’d work in their own mother’s. Every job is backed by our 90-Day Done Right Promise in writing: if it isn’t right, we come back and make it right, no paperwork, no arguing. And because we’ve done this work for over 42 years, we’ll be here for the next forty. That’s not a sales line; it’s why homeowners in Whitney call us back.
We’re trained and equipped on nine gate-automation brands, including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so whatever is on your driveway, we know how to handle it. A live person answers every call, 24 hours a day. Standing offers: $50 Off Any Repair Over $250, a Free Second Opinion on Any Written Estimate, and our $89 Seasonal Tune-Up, plus 5% off for seniors and veterans, always.
Ready for a real price on your Whitney gate? Call (855) 928-1304 for a free, no-pressure estimate. We’ll come out, measure, and hand you a written number you can count on, with no surprises on the bill.
Pricing reflects the Whitney market as of 2026. Ironworks Gate Co. Whitney offers free estimates – call (855) 928-1304.
What Our Customers Say
"The gate works properly now and the price was fair. It did take two visits, because the operator we have is old and the part had to be ordered. They did not charge for the second trip."
- Carrie Mercer"The photo eye was misaligned so the gate refused to close after dark. Ten minute fix. He also cleaned the lens and pointed out that a sprinkler head was spraying it every morning, which is why it kept happening."
- Jamal Dawson"Reprogrammed every clicker in the community and set up the keypad codes. Patient with a very long list of residents."
- Devon Ingram